View HD66712_40905.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HD66712U
(Dot-Matrix Liquid Crystal Display Controller/Driver)
Description
The HD66712 dot-matrix liquid crystal display controller and driver LSI displays alphanumerics, numbers, and symbols. It can be configured to drive a dot-matrix liquid crystal display under the control of a serial or a 4- or 8-bit microprocessor. Since all the functions such as display RAM, character generator, and liquid crystal driver, required for driving a dot-matrix liquid crystal display are internally provided on one chip, a minimum system can be interfaced with this controller/driver. A single HD66712 is capable of displaying a single 24-character line, two 24-character lines, or four 12character lines. The HD66712 software is upwardly compatible with the LCDII (HD44780) which allows the user to easily replace an LCD-II with an HD66712. In addition, the HD66712 is equipped with functions such as segment displays for icon marks, a 4-line display mode, and a horizontal smooth scroll, and thus supports various display forms. This achieves various display forms. The HD66712 character generator ROM is extended to generate 240 5 x 8 dot characters. The low-voltage operation (2.7V) of the HD66712, combined with a low-power mode, is suitable for any portable battery-driven product requiring low power consumption.
Features
* 5 x 8 dot matrix possible * Clock-synchronized serial interface capability; can interface with 4- or 8-bit MPU * Low-power operation support: 2.7 to 5.5V (low voltage) Wide liquid-crystal voltage range: 2.7 to 11.0V max. * Booster for liquid crystal voltage Two/three times (13V max.) * High-speed MPU bus interface (2MHz at 5-V operation)
364
HD66712U
* * * * * * * * * * * Extension driver interface Character display and independent 60-icon mark display possible Horizontal smooth scroll by 6-dot font width display possible 80 x 8-bit display RAM (80 characters max.) 9,600-bit character generator ROM 240 characters (5 x 8 dot) 64 x 8-bit character generator RAM 8 characters (5 x 8 dot) 16 x 8-bit segment icon mark 96-segment icon mark 34-common x 60-segment liquid crystal display driver Programmable duty cycle (See List 1) Software upwardly compatible with HD44780 Wide range of instruction functions: Functions compatible with LCD-II: Display clear, cursor home, display on/off, cursor on/off, display character blink, cursor shift, display shift Additional functions: Icon mark control, 4-line display, horizontal smooth scroll, 6-dot character width control, white-black inverting blinking cursor Automatic reset circuit that initializes the controller/driver after power on (standard version only) Internal oscillator with an external resistor Low power consumption TCP-128 pin, bare-chip
* * * *
List 1 Programmable Duty Cycles
Number of Lines 1 2 3 5-Dot Font Width Duty Ratio 1/17 1/33 1/33 Displayed Characters One 24-character line Two 24-character lines Four 12-character lines Icons 60 60 60 6-Dot Font Width Displayed Characters One 20-character lines Two 20-character lines Four 10-character lines Icons 60 60 60
365
HD66712U
Ordering Information
Type No. HD66712SA00FS HD66712SA01FS HD66712SA02FS HCD66712UA02 HD66712UA02TA0 HD66712UA03TA0 HCD66712UA03 HCD66712UA03BP Package QFP1420-128 (FP-128) QFP1420-128 (FP-128) QFP1420-128 (FP-128) Chip Standard TCP-128 Standard TCP-128 Chip Chip with bump Japanese + European font CGROM Japanese standard Communication European font
366
HD66712U
LCD-II Family Comparison
Item Power supply voltage HD66702 5V 10 % (standard) 2.7V to 5.5V (low voltage) 3.0V to 8.3V 20 characters x 2 lines HD66710 2.7V to 5.5V HD66712S 2.7V to 5.5V HD66712U
Liquid crystal drive voltage Maximum display digits per chip
3.0V to 13.0V 16 characters x 2 lines/ 8 characters x 4 lines 40 segments 9,600 bits (240 5 x 8 dot characters)
3.0V to 13.0V 24 characters x 2 lines/ 12 characters x 4 lines 60 segments 1/17 and 1/33 9,600 bits (240 5 x 8 dot characters)
2.7V to 11.0V
Segment display Display duty cycle CGROM
None 7,200 bits (160 5 x 7 dot characters and 32 5 x 10 dot characters) 64 bytes 80 bytes None 100 16 B External (adjustable)

1/8, 1/11, and 1/16 1/17 and 1/33
CGRAM DDRAM SEGRAM Segment signals Common signals Liquid crystal drive waveform Bleeder resistor for LCD power supply Clock source Rf oscillation frequency (frame frequency)
64 bytes 80 bytes 8 bytes 40 33 B External (adjustable)
64 bytes 80 bytes 16 bytes 60 34 B External (adjustable)

External resistor or External resistor or External resistor or external clock external clock external clock 320 kHz 30% (70 to 130 Hz for 1/8 and 1/16 duty cycle; 51 to 95 Hz for 1/11 duty cycle) 68 k: 5-V operation; 56 k: (3-V operation) 270 kHz 30% (56 to 103 Hz for 1/17 duty cycle; 57 to 106 Hz for 1/33 duty cycle) 91 k: 5-V operation; 75 k: 3-V operation 270 kHz 30% (56 to 103 Hz for 1/17 duty cycle; 57 to 106 Hz for 1/33 duty cycle) 91 k: 5-V operation; 75 k: 3-V operation
Rf resistance
130 k: 5-V operation 110 k: 3-V operation
367
HD66712U
Item Liquid crystal voltage booster circuit Extension driver control signal Reset function Instructions Number of displayed lines Low power mode Horizontal scroll Bus interface CPU bus timing HD66702 None Independent control signal HD66710 2-3 times step-up circuit HD66712S 2-3 times step-up circuit HD66712U
Used in common Independent control with a driver output signal pin
Power on automatic Power on automatic Power on automatic reset reset reset or Reset input Fully compatible with the LCD-II 1 or 2 None Character unit 4 bits/8 bits 1 MHz Uppercompatible with the LCD-II 1, 2, or 4 Available Dot unit 4 bits/8 bits 2 MHz: 5-V operation; 1 MHz: 3-V operation 150 A (typ) Upper compatible with the LCD-II 1, 2, or 4 Available Dot unit Serial; 4 bits/8 bits 2 MHz: 5-V operation; 1 MHz: 3-V operation 150 A (typ) 100 A (LP mode, 1/33 duty) 75 A (LP mode, 1/17 duty) QFP-1420-128 TCP-128 128-pin bare chip

Current consumption
150 A (typ)
120 A (typ) 85 A (LP mode, 1/33 duty) 60 A (LP mode, 1/17 duty) TCP-128 128-pin bare chip
Package
LQFP-2020-144 144-pin bare chip
QFP-1420-100 TQFP-1414-100 100-pin bare chip
368
HD66712U
HD66712 Block Diagram
EXT OSC1 OSC2
CPG Reset circuit ACL RESET* Timing generator
CL1 CL2 M
7 Instruction register (I R) Instruction decoder COM0- COM33 34-bit shift register Common signal driver
8 Address counter 7 RS/CS* R/SCLK RW/SID System interface * Serial * 4 bits * 8 bits
Display data RAM (DDRAM) 80 x 8 bits
D 7 8 SEG1- SEG60 60-bit shift register 60-bit latch circuit
DB4-DB7 Input/ output buffer
8
Data register (DR) 8 Busy flag 3 7
8
Segment signal driver
DB3-DB0
8
8
DB0-SOD Segment RAM (SGRAM) 16 bytes Character generator RAM (CGRAM) 64 bytes Character generator ROM (CGROM) 9,600 bytes Cursor and bling controller LCD drive voltage selector
Vci
C1 C2 V5OUT2 V5OUT3
Booster 5 5/6
Parallel/serial converter and smooth scroll circuit
VCC
GND
V1
V2
V3
V4
V5
369
HD66712U
HCD66712
Dummy 3 2 1 128 101 Dummy 100
Y
Type code HD66712
Chip size (X x Y) Coordinate Origin Pad size (X x Y) Bump size (X x Y)
: : : : :
4.95 x 5.27 mm Pad Center Chip Center 80 x 80 m 70 x 70 m
36 Dummy 37 X 66
67 Dummy
370
HD66712U
HCD66712U Pad Coordinate
Pad No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Function SEG44 SEG45 SEG46 SEG47 SEG48 SEG49 SEG50 SEG51 SEG52 SEG53 SEG54 SEG55 SEG56 SEG57 SEG58 SEG59 SEG60 COM9 COM10 COM11 COM12 COM13 COM14 COM15 COM16 COM25 COM26 COM27 COM28 COM29 COM30 COM31 COM32 COM33 Vcc OSC2 OSC1 CL1 CL2 D M RESET* IM EXT Coordinate X Y -1960 2437 -2120 2437 -2277 2293 -2277 2149 -2277 1872 -2277 1728 -2277 1600 -2277 1472 -2277 1344 -2277 1216 -2277 1088 -2277 960 -2277 832 -2277 704 -2277 576 -2277 448 -2277 320 -2277 192 -2277 64 -2277 -64 -2277 -192 -2277 -320 -2277 -448 -2277 -576 -2277 -704 -2277 -832 -2277 -960 -2277 -1088 -2277 -1216 -2277 -1344 -2277 -1472 -2277 -1600 -2277 -1728 -2277 -1856 -2286 -2158 -2286 -2302 -2120 -2446 -1968 -2446 -1832 -2446 -1704 -2446 -1576 -2446 -1448 -2446 -1320 -2446 -1192 -2446 Pad No. 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 Function TEST GND RS/CS RW/SiD E/SCLK DB0/SOD DB1 DB2 DB3 DB4 DB5 DB6 DB7 Vci C2 C1 GND V5OUT2 V5OUT3 V5 V4 V3 V2 V1 COM24 COM23 COM22 COM21 COM20 COM19 COM18 COM17 COM8 COM7 COM6 COM5 COM4 COM3 COM2 COM1 COM0 SEG1 SEG2 SEG3 Coordinate X Y -1064 -2446 -936 -2446 -792 -2446 -656 -2446 -520 -2446 -384 -2446 -248 -2446 -112 -2446 24 -2446 160 -2446 296 -2446 432 -2446 568 -2446 704 -2446 850 -2446 1001 -2426 1141 -2402 1376 -2446 1640 -2446 1800 -2446 1960 -2446 2120 -2446 2302 -2304 2302 -2162 2277 -1856 2277 -1728 2277 -1600 2277 -1472 2277 -1344 2277 -1216 2277 -1088 2277 -960 2277 -832 2277 -704 2277 -576 2277 -448 2277 -320 2277 -192 2277 -64 2277 64 2277 192 2277 320 2277 448 2277 576 Pad No. 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 -- -- -- -- Function SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34 SEG35 SEG36 SEG37 SEG38 SEG39 SEG40 SEG41 SEG42 SEG43 Dummy1 Dummy2 Dummy3 Dummy4 X Coordinate Y 2277 704 2277 832 2277 960 2277 1088 2277 1216 2277 1344 2277 1472 2277 1600 2277 1728 2277 1872 2277 2149 2277 2293 2120 2437 1960 2437 1800 2437 1656 2437 1512 2437 1368 2437 1224 2437 1080 2437 936 2437 792 2437 648 2437 504 2437 360 2437 216 2437 72 2437 -72 2437 -216 2437 -360 2437 -504 2437 -648 2437 -792 2437 -936 2437 -1080 2437 -1224 2437 -1368 2437 -1512 2437 -1656 2437 -1800 2437 -2277 2437 -2286 -2446 2302 -2446 2277 2437
371
HD66712U
HD66712 Pin Arrangement
SEG43 SEG42 SEG41 SEG40 SEG39 SEG38 SEG37 SEG36 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG44 SEG45 SEG46 SEG47 SEG48 SEG49 SEG50 SEG51 SEG52 SEG53 SEG54 SEG55 SEG56 SEG57 SEG58 SEG59 SEG60 COM9 COM10 COM11 COM12 COM13 COM14 COM15 COM16 COM25 COM26 COM27 COM28 COM29 COM30 COM31 COM32 COM33 VCC OSC2 OSC1 CL1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
HD66712S (Top view)
372
CL2 D M RESET* IM EXT TEST GND RS/CS* RW/SID E/SCLK DB0/SOD DB1 DB2 DB3 DB4 DB5 DB6 DB7 Vci C2 C1 GND V5OUT2 V5OUT3 V5
39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM8 COM17 COM18 COM19 COM20 COM21 COM22 COM23 COM24 V1 V2 V3 V4
TCP Dimensions
COM33 COM32 COM25 COM16 COM9 SEG60
0.65-mm pitch
LCD driver output side
I/O/power supply side
0.24-mm pitch
SEG1 COM0 COM1
COM8 COM17 COM24
NC VCC OSC2 OSC1 CL1 CL2 D M RESET* IM EXT TEST GND RS/CS* RW/SID E/SCLK DB0/SOD DB1 DB2 DB3 DB4 DB5 DB6 DB7 Vci C2 C1 GND V5OUT2 V5OUT3 V5 V4 V3 V2 V1 NC
HD66712U
373
HD66712U
HCD66712U Pad Arrangement
SEG45 SEG44 SEG43 SEG42 SEG41 SEG40 SEG39 SEG38 SEG37 SEG36 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 103 SEG17 102 SEG16 101
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
SEG46 SEG47 SEG48 SEG49 SEG50 SEG51 SEG52 SEG53 SEG54 SEG55 SEG56 SEG57 SEG58 SEG59 SEG60 COM9 COM10 COM11 COM12 COM13 COM14 COM15 COM16 COM25 COM26 COM27 COM28 COM29 COM30 COM31 COM32 COM33 VCC OSC2
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66
104
2
1
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67
SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM8 COM17 COM18 COM19 COM20 COM21 COM22 COM23 COM24 V1 V2
HCD66712U
(Top view)
HD66712 Type code
E/SCLK
DB1
DB2
DB3
DB4
DB5
DB6
DB7
Vci
C2
C1
V5
V4
OSC1
CL1
CL2
RESET*
EXT
TEST
GND
RS/CS*
RW/SID
DB0/SOD
GND
V5OUT2
374
V5OUT3
V3
D
M
IM
HD66712U
Pin Functions
Table 1
Signal IM
Pin Functional Description
Number of Pins 1 I/O I Device Interfaced with -- Function Selects interface mode with the MPU; Low: Serial mode High: 4-bit/8-bit bus mode (Bus width is specified by instruction.) Selects registers during bus mode: Low: Instruction register (write); Busy flag, address counter (read) High: Data register (write/read) Acts as chip-select during serial mode: Low: Select (access enable) High: Not selected (access disable) Selects read/write during bus mode; Low: Write High: Read Inputs serial data during serial mode. Starts data read/write during bus mode; Inputs (Receives) serial clock during serial mode. Four high-order bidirectional tristate data bus pins. Used for data transfer between the MPU and the HD66712. DB7 can be used as a busy flag. Open these pins during serial mode since those signals. Three low order bidirectional tristate data bus pins. Used for data transfer between the MPU and the HD66712. Open these pins during 4-bit operation or serial mode since they are not used. The lowest bidirectional data bit (DB0) during 8-bit bus mode. Open these pins during 4-bit mode since they are not used. Outputs (transfers) serial data during serial mode. Open this pin if reading (transfer) is not performed. Common signals; those that are not used become nonselected waveforms. At 1/17 duty rate, COM1 to COM16 are used for character display, COM0 and COM17 for icon display, and COM18 to COM33 become non-selected waveforms. At 1/33 duty rate, COM1 to COM32 are used for character display, and COM0 and COM33 for icon display. Because two COM signals output the same level simultaneously, apply them according to the wiring pattern of the display device. Segment output signals
RS/CS*
1
I
MPU
RW/SID
1
I
MPU
E/SCLK DB4 to DB7
1 4
I I/O
MPU MPU
DB1 to DB3
3
I/O
MPU
DB0/ SOD 1
I/O /O
MPU
COM0 to COM33
34
O
LCD
SEG1 to SEG60
60
O
LCD
375
HD66712U
Table 1
Signal CL1 CL2 D M EXT
Pin Functional Description (cont)
Number of Pins 1 1 1 1 1 I/O O O O O I Device Interfaced with Extension driver Extension driver Extension driver Extension driver -- Function When EXT = high, outputs the extension driver latch pulse. When EXT = high, outputs the extension driver shift clock. When EXT = high, outputs extension driver data; data from the 61st dot on is output. When EXT = high, outputs the extension driver AC signal. When EXT = high, outputs the extension driver control signal. When EXT = low, the signal becomes tristate and can suppress consumption current. Power supply for LCD drive VCC -V5 = 11V (max) VCC: +2.7V to +5.5V, GND: 0V
V1 to V5 VCC/GND OSC1/ OSC2 Vci
5 2 2
-- -- --
Power supply Power supply
Oscillation resistor When crystal oscillation is performed, an external clock resistor must be connected. When the pin input is an external clock, it must be input to OSC1. -- Inputs voltage to the booster to generate the liquid crystal display drive voltage. Vci is reference voltage and power supply for the booster. Vci = 1.0V to 5.0V VCC Voltage input to the Vci pin is boosted twice and output. When the voltage is boosted three times, the same capacitance as that of C1-C2 should be connected here. Voltage input to the Vci pin is boosted three times and output. External capacitance should be connected here when using the booster. Reset pin. Initialized to "low." Test pin. Should be wired to ground.
1
I
V5OUT2
1
O
V5 pin/ booster capacitance
V5OUT3 C1/C2 RESET* TEST
1 2 1 1
O -- I I
V5 pin Booster capacitance -- --
376
HD66712U
Function Description
System Interface The HD66712 has three types of system interfaces: synchronized serial, 4-bit bus, and 8-bit bus. The serial interface is selected by the IM-pin, and the 4/8-bit bus interface is selected by the DL bit in the instruction register. The HD66712 has two 8-bit registers: an instruction register (IR) and a data register (DR). The IR stores instruction codes, such as display clear and cursor shift, and address information for the display data RAM (DDRAM), the character generator RAM (CGRAM), and the segment RAM (SEGRAM). The MPU can only write to IR, and cannot be read from. The DR temporarily stores data to be written into DDRAM, CGRAM, or SEGRAM. Data written into the DR from the MPU is automatically written into DDRAM, CGRAM, or SEGRAM by an internal operation. The DR is also used for data storage when reading data from DDRAM, CGRAM, or SEGRAM. When address information is written into the IR, data is read and then stored into the DR from DDRAM or CGRAM by an internal operation. Data transfer between the MPU is then completed when the MPU reads the DR. After the read, data in DDRAM, CGRAM, or SEGRAM at the next address is sent to the DR for the next read from the MPU. These two registers can be selected by the registor selector (RS) signal in the 4/8 bit bus interface, and by the RS bit in start byte data in synchronized serial interface (Table 2). Busy Flag (BF) When the busy flag is 1, the HD66712 is in the internal operation mode, and the next instruction will not be accepted. When RS = 0 and R/W = 1 (Table 2), the busy flag is output from DB7. The next instruction must be written after ensuring that the busy flag is 0. Address Counter (AC) The address counter (AC) assigns addresses to DDRAM, CGRAM, or SEGRAM. When an address of an instruction is written into the IR, the address information is sent from the IR to the AC. Selection of DDRAM, CGRAM, and SEGRAM is also determined concurrently by the instruction. After writing into (reading from) DDRAM, CGRAM, or SEGRAM, the AC is automatically incremented by 1 (decremented by 1). The AC contents are then output to DB0 to DB6 when RS = 0 and R/: = 1 (Table 2).
377
HD66712U
Table 2
RS 0 0 1 1
Resistor Selection
R/: 0 1 0 1
:
Operation IR write as an internal operation (display clear, etc.) Read busy flag (DB7) and address counter (DB0 to DB6) DR write as an internal operation (DR to DDRAM, CGRAM, or SEGRAM) DR read as an internal operation (DDRAM, CGRAM, or SEGRAM to DR)
Display Data RAM (DDRAM) Display data RAM (DDRAM) stores display data represented in 8-bit character codes. Its capacity is 80 x 8 bits, or 80 characters. The area in display data RAM (DDRAM) that is not used for display can be used as general data RAM. The DDRAM address (ADD) is set in the address counter (AC) as a hexadecimal number, as shown in Figure 1. The relationship between DDRAM addresses and positions on the liquid crystal display is described and shown on the following pages for a variety of cases.
MSB AC LSB Example: DDRAM address 4E 1 0 0 1 1 1 0
AC6 AC5 AC4 AC3 AC2 AC1 AC0
Figure 1 DDRAM Address
378
HD66712U
* 1-line display (N = 0, and NW = 0) Case 1: When there are fewer than 80 display characters, the display begins at the beginning of DDRAM. For example, when 24 5-dot font-width characters are displayed using one HD66712, the display is generated as shown in Figure 2. When a display shift is performed, the DDRAM addresses shift as well as shown in the figure. When 20 6-dot font-width characters are displayed using one HD66712, the display is generated as shown in Figure 3. Note that COM9 to COM16 begins at address (0A)H in this case 20 characters are displayed. When a display shift is performed, the DDRAM addresses shift as well as shown in the figure. Case 2: Figure 4 shows the case where the EXT pin is fixed high and the HD66712 and the 40output extension driver are used to display 24 6-dot font-width characters. In this case, COM9 to COM16 begins at (0A)H. When a display shift is performed, the DDRAM addresses shift as well as shown in the figure.
1 2 3 4 5 6 7 8 9 10 11 12 COM1 to 8
00 01 02 03 04 05 06 07 08 09 0A 0B
13 14 15 16 17 18 19 20 21 22 23 24
0C 0D 0E 0F 10 11 12 13 14 15 16 17
Display position COM9 to 16 DDRAM address
1 2 3 4 5 6 7 8 9 10 11 12 COM1 to 8
01 02 03 04 05 06 07 08 09 0A 0B 0C
13 14 15 16 17 18 19 20 21 22 23 24
0D 0E 0F 10 11 12 13 14 15 16 17 18
COM9 to 16 (Left shift display) COM9 to 16 (Right shift display)
COM1 to 8
4F 00 01 02 03 04 05 06 07 08 09 0A
0B 0C 0D 0E 0F 10 11 12 13 14 15 16
Figure 2 1-Line by 24-Character Display (5-Dot Font Width)
1 2 3 4 5 6 7 8 9 10 COM1 to 8
00 01 02 03 04 05 06 07 08 09
11 12 13 14 15 16 17 18 19 20
0A 0B 0C 0D 0E 0F 10 11 12 13
Display position COM9 to 16 DDRAM address
1 2 3 4 5 6 7 8 9 10 COM1 to 8
01 02 03 04 05 06 07 08 09 0A
11 12 13 14 15 16 17 18 19 20
0B 0C 0D 0E 0F 10 11 12 13 14
COM9 to 16 (Left shift display) COM9 to 16 (Right shift display)
COM1 to 8
4F 00 01 02 03 04 05 06 07 08
09 0A 0B 0C 0D 0E 0F 10 11 12
Figure 3 1-Line by 20-Character Display (6-Dot Font Width)
379
HD66712U
1 2 3 4 5 6 7 8 9 10 COM1 to 8
00 01 02 03 04 05 06 07 08 09
11 12 13 14 15 16 17 18 19 20
0A 0B 0C 0D 0E 0F 10 11 12 13
21 22 23 24
14 15 16 17
Display position COM9 to 16 DDRAM address
HD66712 SEG1 to SEG60 1 2 3 4 5 6 7 8 9 10 COM1 to 8
01 02 03 04 05 06 07 08 09 0A
HD66712 SEG1 to SEG60 11 12 13 14 15 16 17 18 19 20
0B 0C 0D 0E 0F 10 11 12 13 14
Extension driver SEG1 to SEG24 21 22 23 24
15 16 17 18
COM9 to 16 (Left shift display) COM9 to 16 (Right shift display)
COM1 to 8
4F 00 01 02 03 04 05 06 07 08
09 0A 0B 0C 0D 0E 0F 10 11 12
13 14 15 16
Figure 4 1-Line by 24-Character Display (6-Dot Font Width)
380
HD66712U
* 2-line display (N = 1, and NW = 0) Case 1: The first line is displayed from COM1 to COM16, and the second line is displayed from COM17 to COM32. Note that the last address of the first line and the first address of the second line are not consecutive. Figure 5 shows an example where a 5-dot font-width 24 x 2-line display is performed using one HD66712. Here, COM9 to COM16 begins at (0C)H, and COM25 to COM32 at (4C)H. When a display shift is performed, the DDRAM addresses shift as shown. Figure 6 shows an example where a 6-dot font-width 20 x 2-line display is performed using one HD66712. COM9 to COM16 begins at (0A)H, and COM25 to COM32 at (4A)H.
1 2 3 4 5 6 7 8 9 10 11 12 COM1 to COM8 COM17 to COM24
00 01 02 03 04 05 06 07 08 09 0A 0B
13 14 15 16 17 18 19 20 21 22 23 24
0C 0D 0E 0F 10 11 12 13 14 15 16 17
Display position COM9 to COM16 COM25 to COM32 DDRAM address
40 41 42 43 44 45 46 47 48 49 4A 4B
4C 4D 4E 4F 50 51 52 53 54 55 56 57
1 2 3 4 5 6 7 8 9 10 11 12 COM1 to COM8 COM1 COM17 to COM24 COM1 to COM8 COM17 to COM24
01 02 03 04 05 06 07 08 09 0A 0B 0C
13 14 15 16 17 18 19 20 21 22 23 24
0D 0E 0F 10 11 12 13 14 15 16 17 18
COM9 to COM16
41 42 43 44 45 46 47 48 49 4A 4B 4C
4D 4E 4F 50 51 52 53 54 55 56 57 58
(Left shift COM25 to display) COM32 COM9 to COM16
27 00 01 02 03 04 05 06 07 08 09 0A
0B 0C 0D 0E 0F 10 11 12 13 14 15 16
67 40 41 42 43 44 45 46 47 48 49 4A
4B 4C 4D 4E 4F 50 51 52 53 54 55 56
(Right shift COM25 to display) COM32
Figure 5 2-Line by 24-Character Display (5-Dot Font Width)
1 2 3 4 5 6 7 8 9 10 COM1 to COM8 COM17 to COM24
00 01 02 03 04 05 06 07 08 09
11 12 13 14 15 16 17 18 19 20
0A 0B 0C 0D 0E 0F 10 11 12 13
Display position COM9 to COM16 COM25 to COM32 DDRAM address
40 41 42 43 44 45 46 47 48 49
4A 4B 4C 4D 4E 4F 50 51 52 53
Figure 6 2-Line by 20-Character Display (6-Dot Font Width)
381
HD66712U
Case 2: Figure 7 shows the case where the EXT pin is fixed high and the HD66712 and the 40output extension driver are used to extend the number of display characters to 32 5-dot font-width characters. In this case, COM9 to COM16 begins at (0C)H, and COM25 to COM32 at (4C)H. When a display shift is performed, the DDRAM addresses shift as shown.
1 2 3 4 5 6 7 8 9 10 11 12 COM1 to COM8 COM17 to COM24
00 01 02 03 04 05 06 07 08 09 0A 0B
13 14 15 16 17 18 19 20 21 22 23 24
0C 0D 0E 0F 10 11 12 13 14 15 16 17
25 26 27 28 29 30 31 32
18 19 1A 1B 1C 1D 1E 1F
Display position COM9 to COM16 COM25 to COM32 DDRAM address
40 41 42 43 44 45 46 47 48 49 4A 4B
4C 4D 4E 4F 50 51 52 53 54 55 56 57
58 59 5A 5B 5C 5D 5E 5F
HD66712 SEG1-SEG60 1 2 3 4 5 6 7 8 9 10 11 12 COM1 to COM8 COM1 COM17 to COM24 COM1 to COM8 COM17 to COM24
01 02 03 04 05 06 07 08 09 0A 0B 0C
HD66712 SEG1-SEG60 13 14 15 16 17 18 19 20 21 22 23 24
0D 0E 0F 10 11 12 13 14 15 16 17 18
Extension driver Seg1-Seg40 25 26 27 28 29 30 31 32 (Left shift display)
19 1A 1B 1C 1D 1E 1F 20
COM9 to COM16 COM25 to COM32 (Right shift display)
41 42 43 44 45 46 47 48 49 4A 4B 4C
4D 4E 4F 50 51 52 53 54 55 56 57 58
59 5A 5B 5C 5D 5E 5F 60
27 00 01 02 03 04 05 06 07 08 09 0A
0B 0C 0D 0E 0F 10 11 12 13 14 15 16
17 18 19 1A 1B 1C 1D 1E
COM9 to COM16 COM25 to COM32
67 40 41 42 43 44 45 46 47 48 49 4A
4B 4C 4D 4E 4F 50 51 52 53 54 55 56
57 58 59 5A 5B 5C 5D 5E
Figure 7 2-Line by 32 Character Display (5-Dot Font Width)
382
HD66712U
* 4-line display (NW = 1) Case 1: The first line is displayed from COM1 to COM8, the second line is displayed from COM9 to COM16, the third line is displayed from COM17 to COM24, and the fourth line is displayed from COM25 to COM32. Note that the DDRAM addresses of each line are not consecutive. Figure 8 shows an example where a 12 x 4-line display is performed using one HD66712. When a display shift is performed, the DDRAM addresses shift as shown.
1 2 3 4 5 6 7 8 9 10 11 12 COM1 to 8 COM9 to 16 COM17 to 24 COM25 to 32
00 01 02 03 04 05 06 07 08 09 0A 0B 20 21 22 23 24 25 26 27 28 29 2A 2B
Display position
DDRAM address
40 41 42 43 44 45 46 47 48 49 4A 4B 60 61 62 63 64 65 66 67 68 69 6A 6B
(Left shift display) 1 2 3 4 5 6 7 8 9 10 11 12 COM1 to 8 COM9 to 16 COM17 to 24 COM25 to 32
01 02 03 04 05 06 07 08 09 0A 0B 0C 21 22 23 24 25 26 27 28 29 2A 2B 2C 41 42 43 44 45 46 47 48 49 4A 4B 4C 61 62 63 64 65 66 67 68 69 6A 6B 6C
(Right shift display) 1 2 3 4 5 6 7 8 9 10 11 12
13 00 01 02 03 04 05 06 07 08 09 0A 33 20 21 22 23 24 25 26 27 28 29 2A 53 40 41 42 43 44 45 46 47 48 49 4A 73 60 61 62 63 64 65 66 67 68 69 6A
Figure 8 4-Line Display
383
HD66712U
Case 2: Figure 9 shows the case where the EXT pin is fixed high and the HD66712 and the 40output extension driver are used to extend the number of display characters. When a display shift is performed, the DDRAM addresses shift as shown.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 COM1 to 8 COM9 to 16 COM17 to 24 COM25 to 32
00 01 02 03 04 05 06 07 08 09 0A 0B 20 21 22 23 24 25 26 27 28 29 2A 2B 40 41 42 43 44 45 46 47 48 49 4A 4B 60 61 62 63 64 65 66 67 68 69 6A 6B 0C 0D 0E 0F 10 11 12 13 2C 2D 2E 2F 30 31 32 33
Display position
DDRAM address
4C 4D 4E 4F 50 51 52 53 6C 6D 6E 6F 70 71 72 73
HD66712
Extension driver
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
01 02 03 04 05 06 07 08 09 0A 0B 0C 21 22 23 24 25 26 27 28 29 2A 2B 2C 41 42 43 44 45 46 47 48 49 4A 4B 4C 61 62 63 64 65 66 67 68 69 6A 6B 6C 0D 0E 0F 10 11 12 13 00 2D 2E 2F 30 31 32 33 20 4D 4E 4F 50 51 52 53 40 6D 6E 6F 70 71 72 73 60
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
13 00 01 02 03 04 05 06 07 08 09 0A 33 20 21 22 23 24 25 26 27 28 29 2A 53 40 41 42 43 44 45 46 47 48 49 4A 73 60 61 62 63 64 65 66 67 68 69 6A 0B 0C 0D 0E 0F 10 11 12 2B 2C 2D 2E 2F 30 31 32 4B 4C 4D 4E 4F 50 51 52 6B 6C 6D 6E 6F 70 71 72
(Left shift display)
(Right shift display)
Figure 9 4-Line by 20-Character Display
384
HD66712U
Character Generator ROM (CGROM) The character generator ROM generates 5 x 8 dot character patterns from 8-bit character codes (Table 3 to 6). It can generate 240 5 x 8 dot character patterns. User-defined character patterns are also available using a mask-programmed ROM (see "Modifying Character Patterns.") Character Generator RAM (CGRAM) The character generator RAM allows the user to redefine the character patterns. In the case of 5 x 8 characters, up to eight may be redefined. Write the character codes at the addresses shown as the left column of Table 3 to 6 to show the character patterns stored in CGRAM. See Table 7 for the relationship between CGRAM addresses and data and display patterns. Segment RAM (SEGRAM) The segment RAM (SEGRAM) is used to enable control of segments such as an icon and a mark by the user program. For a 1-line display, SEGRAM is read from the COM0 and the COM17 output, and for 2- or 4-line displays, it is read from the COM0 and the COM33 output, to perform 60-segment display (80-segment display when using the extension driver). As shown in Table 8, bits in SEGRAM corresponding to segments to be displayed are directly set by the MPU, regardless of the contents of DDRAM and CGRAM. SEGRAM data is stored in eight bits. The lower six bits control the display of each segment, and the upper two bits control segment blinking. Timing Generation Circuit The timing generation circuit generates timing signals for the operation of internal circuits such as DDRAM, CGROM, CGRAM, and SEGRAM. RAM read timing for display and internal operation timing by MPU access are generated separately to avoid interfering with each other. Therefore, when writing data to DDRAM, for example, there will be no undesirable interferences, such as flickering, in areas other than the display area.
385
HD66712U
Liquid Crystal Display Driver Circuit The liquid crystal display driver circuit consists of 34 common signal drivers and 60 segment signal drivers. When the character font and number of lines are selected by a program, the required common signal drivers automatically output drive waveforms, while the other common signal drivers continue to output non-selection waveforms. Character pattern data is sent serially through a 60-bit shift register and latched when all needed data has arrived. The latched data then enables the driver to generate drive waveform outputs. Sending serial data always starts at the display data character pattern corresponding to the last address of the display data RAM (DDRAM). Since serial data is latched when the display data character pattern corresponding to the starting address enters the internal shift register, the HD66712 drives from the head display. Cursor/Blink Control Circuit The cursor/blink (or white-black inversion) control is used to produce a cursor or a flashing area on the display at a position corresponding to the location in stored in the address counter (AC). For example (Figure 10), when the address counter is (08)H, a cursor is displayed at a position corresponding to DDRAM address (08)H. Scroll Control Circuit The scroll control circuit is used to perform a smooth-scroll in the unit of dot. When the number of characters to be displayed is greater than that possible at one time on the liquid crystal module, this horizontal smooth scroll can be used to display all characters.
AC = (08)16 1 2 3 4 5 6 7 8 9 10 11 Display position DDRAM address
00 01 02 03 04 05 06 07 08 09 0A
Cursor position
Figure 10 Cursor/Blink Display Example
386
HD66712U
Table 3 Relationship between Character Codes and Character Patterns (ROM Code: A00)
Upper Bits
Lower Bits
0000
CG RAM (1) CG RAM (2) CG RAM (3) CG RAM (4) CG RAM (5) CG RAM (6) CG RAM (7) CG RAM (8) CG RAM (1) CG RAM (2) CG RAM (3) CG RAM (4) CG RAM (5) CG RAM (6) CG RAM (7) CG RAM (8)
0001
0010 0011 0100 0101 0110 0111
1000 1001 1010 1011 1100 1101 1110 1111
xxxx0000
xxxx0001
xxxx0010
xxxx0011
xxxx0100
xxxx0101
xxxx0110
xxxx0111
xxxx1000
xxxx1001
xxxx1010
xxxx1011
xxxx1100
xxxx1101
xxxx1110
xxxx1111
387
HD66712U
Table 4 Relationship between Character Codes and Character Pattern (ROM Code: A01)
Upper Bits
Lower Bits
0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111
CG RAM (1) CG RAM (2) CG RAM (3) CG RAM (4) CG RAM (5) CG RAM (6) CG RAM (7) CG RAM (8) CG RAM (1) CG RAM (2) CG RAM (3) CG RAM (4) CG RAM (5) CG RAM (6) CG RAM (7) CG RAM (8)
xxxx0000
xxxx0001
xxxx0010
xxxx0011
xxxx0100
xxxx0101
xxxx0110
xxxx0111
xxxx1000
xxxx1001
xxxx1010
xxxx1011
xxxx1100
xxxx1101
xxxx1110
xxxx1111
388
HD66712U
Table 5 Relationship between Character Codes and Character Patterns (ROM Code: A02)
Upper Bits
Lower Bits
0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111
CG RAM (1) CG RAM (2) CG RAM (3) CG RAM (4) CG RAM (5) CG RAM (6) CG RAM (7) CG RAM (8) CG RAM (1) CG RAM (2) CG RAM (3) CG RAM (4) CG RAM (5) CG RAM (6) CG RAM (7) CG RAM (8)
xxxx0000
xxxx0001
xxxx0010
xxxx0011
xxxx0100
xxxx0101
xxxx0110
xxxx0111
xxxx1000
xxxx1001
xxxx1010
xxxx1011
xxxx1100
xxxx1101
xxxx1110
xxxx1111
Note: The character codes of the characters enclosed in the bold frame are the same as those of the first edition of the ISO8859 and the character code compatible.
389
HD66712U
Table 6 Relationship between Character Codes and Character Pattern (ROM Code: A03)
Upper Bits
Lower Bits
0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111
CG RAM (1) CG RAM (2) CG RAM (3) CG RAM (4) CG RAM (5) CG RAM (6) CG RAM (7) CG RAM (8) CG RAM (1) CG RAM (2) CG RAM (3) CG RAM (4) CG RAM (5) CG RAM (6) CG RAM (7) CG RAM (8)
xxxx0000
xxxx0001
xxxx0010
xxxx0011
xxxx0100
xxxx0101
xxxx0110
xxxx0111
xxxx1000
xxxx1001
xxxx1010
xxxx1011
xxxx1100
xxxx1101
xxxx1110
xxxx1111
390
HD66712U
Table 7 Example of Relationships between Character Code (DDRAM) and Character Pattern(CGRAM Data)
a) When character pattern is 5 x 8 dots Character code (DDRAM data) D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 * 0 0 0 CGRAM address A5 A4 A3 0 0 0 A2 A1 A0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
MSB
CGRAM data
LSB
O7 O6 O5 O4 O3 O2 O1 O0 * * * 1 1 1 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 1 1 1 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 1 1 1 0 0 0 0 0 1 1 1 0 0 0 0 0
Character pattern (1)
0
0
0
0
*
1
1
1
1
1
1
*
*
*
Character pattern (8)
a) When character pattern is 6 x 8 dots Character code (DDRAM data) D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 * 0 0 0 CGRAM address A5 A4 A3 A2 A1 A0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
MSB
CGRAM data
LSB
O7 O6 O5 O4 O3 O2 O1 O0 * * 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 1 1 1 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 1 1 1 0 0 0 0 0 1 1 1 0 0 0 0 0
Character pattern (1)
0
0
0
0
*
1
1
1
1
1
1
*
*
Character pattern (8)
391
HD66712U
Notes: 1. Character code bits 0 to 2 correspond to CGRAM address bits 3 to 5 (3 bits: 8 types). 2. CGRAM address bits 0 to 2 designate the character pattern line position. The 8th line is the cursor position and its display is formed by a logical OR with the cursor. 3. The character data is stored with the rightmost character element in bit 0, as shown in the figure above. Characters of 5 dots in width (FW = 0) are stored in bits 0 to 4, and characters of 6 dots in width (FW = 1) are stored in bits 0 to 5. 4. When the upper four bits (bits 7 to 4) of the character code are 0, CGRAM is selected. Bit 3 of the character code is invalid (*). Therefore, for example, the character codes (00)H and (08)H correspond to the same CGRAM address. 5. A set bit in the CGRAM data corresponds to display selection, and 0 to non-selection. 6. When the BE bit of the function set register is 1, pattern blinking control of the lower six bits is controlled using the upper two bits (bits 7 and 6) in CGRAM. When bit 7 is 1, of the lower six bits, only those which are set are blinked on the display. When bit 6 is 1, a bit 4 pattern can be blinked as for a 5-dot font width, and a bit 5 pattern can be blinked as for a 6-dot font width. * Indicates no effect.
392
HD66712U
Table 8 Relationship between SEGRAM Addresses and Display Patterns
SEGRAM data a) 5-dot font width D7 D6 D5 D4 D3 D2 D1 D0 B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 * B1 B0 *
Blinking control
SEGRAM address A3 A2 A1 A0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
b) 6-dot font width D7 D6 D5 D4 D3 D2 D1 D0 B1 B0 S1 S2 S3 S4 S5 S6 B1 B0 S7 S8 S9 S10 S11 S12 B1 B0 S13 S14 S15 S16 S17 S18 B1 B0 S19 S20 S21 S22 S23 S24 B1 B0 S25 S26 S27 S28 S29 S30 B1 B0 S31 S32 S33 S34 S35 S36 B1 B0 S37 S38 S39 S40 S41 S42 B1 B0 S43 S44 S45 S46 S47 S48 B1 B0 S49 S50 S51 S52 S53 S54 B1 B0 S55 S56 S57 S58 S59 S60 B1 B0 S61 S62 S63 S64 S65 S66 B1 B0 S67 S68 S69 S70 S71 S72 B1 B0 S73 S74 S75 S76 S77 S78 B1 B0 S79 S80 S81 S82 S83 S84 B1 B0 S85 S86 S87 S88 S89 S90 B1 B0 S91 S92 S93 S94 S95 S96
Blinking control Pattern on/off
S1 S2 S3 S4 S5 S6 S7 S8 S9 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 S22 S23 S24 S25 S26 S27 S28 S29 S30 S31 S32 S33 S34 S35 S36 S37 S38 S39 S40 S41 S42 S43 S44 S45 S46 S47 S48 S49 S50 S51 S52 S53 S54 S55 S56 S57 S58 S59 S60 S61 S62 S63 S64 S65 S66 S67 S68 S69 S70 S71 S72 S73 S74 S75 S76 S77 S78 S79 S80
Pattern on/off
Notes: 1. Data set to SEGRAM is output when COM0 and COM17 are selected, as for a 1-line display, and output when COM0 and COM33 are selected, as for a 2-line or a 4-line display. COM0 and COM17 for a 1-line display and COM0 and COM33 for a 2-line or a 4-line display are the same signals. 2. S1 to S96 are pin numbers of the segment output driver. S1 is positioned to the left of the display. When the HD66712 is used by one chip, segments from S1 to S60 are displayed. An extension driver displays the segments after S61. 3. After S80 output at 5-dot font and S96 output at 6-dot font, S1 output is repeated again. 4. As for a 5-dot font width, lower five bits (D4 to D0) are display on.off information of each segment. For a 6-dot character width, the lower six bits (D5 to D0) are the display information for each segment. 5. When the BE bit of the function set register is 1, pattern blinking of the lower six bits is controlled using the upper two bits (bits 7 and 6) in SEGRAM. When bit 7 is 1, only a bit set to "1" of the lower six bits is blinked on the display. When bit 6 is 1, only a bit 4 pattern can be blinked as for a 5-dot font width, and only a bit 5 pattern can be blinked as for 6-dot font width. 6. Bit 5 (D5) is invalid for a 5-dot font width. 7. Set bits in the SEGRAM data correspond to display selection, and zeros to non-selection.
393
HD66712U
i) 5-dot font width (FW = 0)
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S56
S57
S58
S60 S59
S61
S62
S63
S65 S64
SEG10
SEG56
SEG57
SEG58
SEG59
SEG60
SEG61
SEG62
SEG63
SEG64
S64
Displayed by HD66712
Displayed by extension driver
ii) 6-dot font width (FW = 1)
S1
S2
S3
S4
S5
S6
S7
S8
S9
S11 S10
S12
S55
S56
S57
S59 S58
S60
S61
S62
S63
S65
SEG65
S66
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG10
SEG9
SEG11
SEG12
SEG55
SEG56
SEG57
SEG58
SEG59
SEG60
Seg61
Seg62
Seg63
Seg64
Seg65
Displayed by HD66712
Displayed by extension driver
Figure 11 Correspondence between SEGRAM and Segment Display
394
Seg66
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
HD66712U
Modifying Character Patterns * Character pattern development procedure The following operations correspond to the numbers listed in Figure 12: a. Determine the correspondence between character codes and character patterns. b. Create a listing indicating the correspondence between EPROM addresses and data. c. Program the character patterns into an EPROM. d. Send the EPROM to Hitachi. e. Computer processing of the EPROM is performed at Hitachi to create a character pattern listing, which is sent to the user. f. If there are no problems within the character pattern listing, a trial LSI is created at Hitachi and samples are sent to the user for evaluation. When it is confirmed by the user that the character patterns are correctly written, mass production of the LSI will proceed at Hitachi.
395
HD66712U
Hitachi User Start
Computer processing Create character pattern listing Evaluate character patterns No
Determine character patterns Create EPROM address data listing
1
5
2
Write EPROM
3
EPROM Hitachi OK? Yes Art work
4
M/T
Masking
Trial
Sample
Sample evaluation
6
OK? Yes Mass production
No
Figure 12 Character Pattern Development Procedure
396
HD66712U
Programming Character Patterns This section explains the correspondence between addresses and data used to program character patterns in EPROM. * Programming to EPROM The HD66712 character generator ROM can generate 240 5 x 8 dot character patterns. Table 9 shows correspondence between the EPROM address data and the character pattern. Handling Unused Character Patterns 1. EPROM data outside the character pattern area: This is ignored by the character generator ROM for display operation so any data is acceptable. 2. EPROM data in CGRAM area: Always fill with zeros. 3. Treatment of unused user patterns in the HD66712 EPROM: According to the user application, these are handled in either of two ways: a When unused character patterns are not programmed: If an unused character code is written into DDRAM, all its dots are lit, because the EPROM is filled with 1s after it is erased. b When unused character patterns are programmed as 0s: Nothing is displayed even if unused character codes are written into DDRAM. (This is equivalent to a space.) Table 9 Example of Correspondence between EPROM Address Data and Character Pattern (5 x 8 Dots)
EPROM Address A11 A10 A9 A8 A7 A6 A5 A4 A3 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0 0 Character code A2 A1 A0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Data
MSB
LSB
O4 O3 O2 O1 O0 1 1 1 0 0 0 0 0001 0001 0001 010 0100 0100 0100 0000
01
"0" Line position
Notes: 1. EPROM addresses A11 to A4 correspond to a character code. 2. EPROM addresses A2 to A0 specify the line position of the character pattern. EPROM address A3 should be set to "0." 3. EPROM data O4 to O0 correspond to character pattern data. 4. Areas which are lit (indicated by shading) are stored as "1," and unlit areas as "0." 5. The eighth line is also stored in the CGROM, and should also be programmed. If the eighth line is used for a cursor, this data should all be set to zero. 6. EPROM data bits 07 to 05 are invalid. 0 should be written in all bits.
397
HD66712U
Reset Function
Initializing by Internal Reset Circuit An internal reset circuit automatically initializes the HD66712 when the power is turned on. The following instructions are executed during the initialization. The busy flag (BF) is kept in the busy state until the initialization ends (BF = 1). The busy state lasts for 15 ms after VCC rises to 4.5V or 40 ms after the VCC rises to 2.7V. 1. Display clear: (20)H to all DDRAM 2. Set functions: DL = 1: 8-bit interface data N = 1: 2-line display RE = 0: Extension register write disable BE = 0: CGRAM/SEGRAM blink off LP = 0: Not in low power mode 3. Control display on/off: D = 0: Display off C = 0: Cursor off B = 0: Blinking off 4. Set entry mode: I/D = 1: Increment by 1 S = 0: No shift 5. Set extension function: FW = 0: 5-dot character width B/W = 0: Normal cursor (eighth line) NW = 0: 1- or 2-line display (depending on N) 6. Enable scroll: HSE = 0000: Scroll unable 7. Set scroll amount: HDS = 000000: Not scroll Note: If the electrical characteristics conditions listed under the Table Power Supply Conditions Using Internal Reset Circuit are not met, the internal reset circuit will not operate normally and will fail to initialize the HD66712. Initializing by Hardware Reset Input The HD66712 also has a reset input pin: RESET*. If this pin is made low during operation, an internal reset and initialization is performed. This pin is ignored, however, during the internal reset period at power-on.
398
HD66712U
Interfacing to the MPU
The HD66712 can send data in either two 4-bit operations or one 8-bit operation, thus allowing interfacing with 4- or 8-bit MPUs. * For 4-bit interface data, only four bus lines (DB4 to DB7) are used for transfer. Bus lines DB0 to DB3 are disabled. The data transfer between the HD66712 and the MPU is completed after the 4-bit data has been transferred twice. As for the order of data transfer, the four high order bits (for 8-bit operation, DB4 to DB7) are transferred before the four low order bits (for 8-bit operation, DB0 to DB3). The busy flag must be checked (one instruction) after the 4-bit data has been transferred twice. Two more 4-bit operations then transfer the busy flag and address counter data. * For 8-bit interface data, all eight bus lines (DB0 to DB7) are used. * When the IM pin is low, the HD66712 uses a serial interface. See "Transferring Serial Data."
RS R/W E
DB7 DB6 DB5 DB4
IR7 IR6 IR5 IR4
IR3 IR2 IR1 IR0
BF AC6 AC5 AC4
AC3 AC2 AC1 AC0
DR7 DR6 DR5 DR4
DR3 DR2 DR1 DR0
Instruction register (IR) write
Busy flag (BF) and address counter (AC) read
Data register (DR) read
Figure 13 4-Bit Transfer Example
399
HD66712U
Transferring Serial Data When the IM pin (interface mode) is low, the HD66712 enters serial interface mode. A three-line clocksynchronous transfer method is used. The HD66712 receives serial input data (SID) and transmits serial output data (SOD) by synchronizing with a transfer clock (SCLK) sent from the master side. When the HD66712 interfaces with several chips, chip select pin (CS*) must be used. The transfer clock (SCLK) input is activated by making chip select (CS*) low. In addition, the transfer counter of the HD66712 can be reset and serial transfer synchronized by making chip select (CS*) high. Here, since the data which was being sent at reset is cleared, restart the transfer from the first bit of this data. In the case of a minimum 1 to 1 transfer system with the HD66712 used as a receiver only, an interface can be established by the transfer clock (SCLK) and serial input data (SID). In this case, chip select (CS*) should be fixed to low. The transfer clock (SCLK) is independent from operational clock (CLK) of the HD66712. However, when several instructions are continuously transferred, the instruction execution time determined by the operational clock (CLK) (see continuous transfer) must be considered since the HD66712 does not have an internal transmit/receive buffer. To begin with, transfer the start byte. By receiving five consecutive bits (synchronizing bit string) at the beginning of the start byte, the transfer counter of the HD66712 is reset and serial transfer is synchronized. The 2 bits following the synchronizing bit string (5 bits) specify transfer direction (R/: bit) and register select (RS bit). Be sure to transfer 0 in the 8th bit. After receiving the start byte, instructions are received and the data/busy flag is transmitted. When the transfer direction and register select remain the same, data can be continuously transmitted or received. The transfer protocol is described in detail below. * Receiving (write) After receiving the start synchronization bits, the R/: bit (= 0), and the RS bit with the start byte, an 8-bit instruction is received in 2 bytes: the lower 4 bits of the instruction are placed in the LSB of the first byte, and the higher 4 bits of the instruction are placed in the LSB of the second byte. Be sure to transfer 0 in the following 4 bits of each byte. When instructions are continuously received with R/: bit and RS bit unchanged, continuous transfer is possible (see "Continuous Transfer" below).
400
HD66712U
a) Basic transfer serial data input (receive) CS* (input)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
SCLK (input) SID (input)
1 1 1 1 1 R/W RS 0 D0 D1 D2 D3 0 0 0 0 D4 D5 D6 D7 0 0 0 0
Synchronizing bit string
Lower data 1st byte
Upper data 2nd byte Instruction
Starting byte
b) Basic transfer of serial data output (transmit) CS* (input)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SCLK (input) SID (input) SOD (output) Synchronizing bit string Starting byte
1 1 1 1 1 R/W RS 0 0 0 0 0 0 0 0 0
D0 D1 D2 D3 D4 D5 D6 D7
Lower data
Upper data
Busy flag/data read
Figure 14 Basic Procedure for Transferring Serial Data
401
HD66712U
* Transmitting (read) After receiving the start synchronization bits, the R/: bit (= 1), and the RS bit with the start byte, 8bit read data is transmitted in the same way as receiving. When read data is continuously transmitted with R/: bit and RS bit unchanged, continuous transfer is possible (see "Continuous Transfer" below). Even at the time of the transmission (the data output), since the HD66712 monitors the start synchronization bit string ("11111") by the SID input, the HD66712 receives the R/W bit and RS bit after detecting the start synchronization. Therefore, in the case of a continuous transfer, fix the SID input "0." * Continuous transfer When instructions are continuously received with the R/: bit and RS bit unchanged, continuous receive is possible without inserting a start byte between instructions. After receiving the last bit (the 8th bit in the 2nd byte) of an instruction, the system begins to execute it. To execute the next instruction, the instruction execution time of the HD66712 must be considered. If the last bit (the 8th bit in the 2nd byte) of the next instruction is received during execution of the previous instruction, the instruction will be ignored. In addition, if the next unit of data is read before read execution of previous data is completed for busy flag/address counter/RAM data, normal data is not sent. To transfer data normally, the busy flag must be checked. However, it is possible to transfer without reading the busy flag if wiring for transmission (SOD pin) needs to be reduced or if the burden of polling on the MPU needs to be removed. In this case, insert a transfer wait so that the current instruction first completes execution during instruction transfer.
402
HD66712U
i) Continuous data write by boring processing SCLK (input) SID (input) SOD (output) Instruction (1) Execution time ii) Continuous data write by CPU wait insert Wait SCLK (input) SID (input) Instruction (1) 1st byte 2nd byte Instruction (2) 1st byte 2nd byte Instruction (1) Execution time Wait Instruction (3) 1st byte 2nd byte Instruction (2) Execution time Instruction (3) Execution time
Start byte
Instruction (1) 1st byte 2nd byte
Start byte Busy read
Start byte
Instruction (2) 1st byte 2nd byte
Instruction waiting time (not busy state)
Start byte
iii) Continuous data read by CPU wait insert SCLK (input) SID (input) SOD (output) Instruction (1) Execution time Wait Start byte Data read (1) Instruction (2) Execution time Data read (2) Wait
Figure 15 Procedure for Continuous Data Transfer
403
HD66712U
Instructions
Outline Only the instruction register (IR) and the data register (DR) of the HD66712 can be controlled by the MPU. Before starting internal operation of the HD66712, control information is temporarily stored in these registers to allow interfacing with various MPUs, which operate at different speeds, or various peripheral control devices. The internal operation of the HD66712 is determined by signals sent from the MPU. These signals, which include register selection (RS), read/write (R/:), and the data bus (DB0 to DB7), make up the HD66712 instructions (Table 12). There are four categories of instructions that: * * * * Designate HD66712 functions, such as display format, data length, etc. Set internal RAM addresses Perform data transfer with internal RAM Perform miscellaneous functions
Normally, instructions that perform data transfer with internal RAM are used the most. However, autoincrementation by 1 (or auto-decrementation by 1) of internal HD66712 RAM addresses after each data write can lighten the program load of the MPU. Since the display shift instruction (Table 10) can perform concurrently with display data write, the user can minimize system development time with maximum programming efficiency. When an instruction is being executed for internal operation, no instruction other than the busy flag/address read instruction can be executed. Because the busy flag is set to 1 while an instruction is being executed, check it to make sure it is 0 before sending another instruction from the MPU. Note: Be sure the HD66712 is not in the busy state (BF = 1) before sending an instruction from the MPU to the HD66712. If an instruction is sent without checking the busy flag, the time between the first instruction and next instruction will take much longer than the instruction time itself. Refer to Table 12 for the list of each instruction execution time.
404
HD66712U
Instruction Description
Clear Display Clear display writes space code (20)H (character pattern for character code (20)H must be a blank pattern) into all DDRAM addresses. It then sets DDRAM address 0 into the address counter, and returns the display to its original status if it was shifted. In other words, the display disappears and the cursor or blinking goes to the left edge of the display (in the first line if 2 lines are displayed). It also sets I/D to 1 (increment mode) in entry mode. S of entry mode does not change. Return Home Return home sets DDRAM address 0 into the address counter, and returns the display to its original status if it was shifted. The DDRAM contents do not change. The cursor or blinking goes to the left edge of the display (in the first line if 2 lines are displayed). In addition, flicker may occur in a moment at the time of this instruction issue. Entry Mode Set I/D: Increments (I/D = 1) or decrements (I/D = 0) the DDRAM address by 1 when a character code is written into or read from DDRAM. The cursor or blinking moves to the right when incremented by 1 and to the left when decremented by 1. The same applies to writing and reading of CGRAM and SEGRAM. S: Shifts the entire display either to the right (I/D = 0) or to the left (I/D = 1) when S is 1 during DDRAM write. The display does not shift if S is 0. If S is 1, it will seem as if the cursor does not move but the display does. The display does not shift when reading from DDRAM. Also, writing into or reading out from CGRAM and SEGRAM does not shift the display. In a low power mode (LP = 1), do not set S = 1 because the whole display does not normally shift. Display On/Off Control When extension register enable bit (RE) is 0, bits D, C, and B are accessed. D: The display is on when D is 1 and off when D is 0. When off, the display data remains in DDRAM, but can be displayed instantly by setting D to 1. C: The cursor is displayed when C is 1 and not displayed when C is 0. Even if the cursor disappears, the function of I/D or other specifications will not change during display data write. The cursor is displayed using 5 dots in the 8th line for 5 x 8 dot character font.
405
HD66712U
B: The character indicated by the cursor blinks when B is 1. The blinking is displayed as switching between all blank dots and displayed characters at a speed of 370-ms intervals when fcp or fOSC is 270 kHz. The cursor and blinking can be set to display simultaneously. (The blinking frequency changes according to fOSC or the reciprocal of fcp. For example, when fcp is 300 kHz, 370 x 270/300 = 333 ms.) Extended Function Set When the extended register enable bit (RE) is 1, FW, B/W, and NW bit shown below are accessed. Once these registers are accessed, the set values are held even if the RE bit is set to zero. FW: When FW is 1, each displayed character is controlled with a 6-dot width. The user font in CGRAM is displayed with a 6-bit character width from bits 5 to 0. As for fonts stored in CGROM, no display area is assigned to the left most bit, and the font is displayed with a 5-bit character width. If the FW bit is changed, data in DDRAM and CGRAM SEGRAM is destroyed. Therefore, set FW before data is written to RAM. When font width is set to 6 dots, the frame frequency decreases to 5/6 compared to 5-dot time. See "Oscillator Circuit" for details. B/W: When B/W is 1, the character at the cursor position is cyclically displayed with black-white inversion. At this time, bits C and B in display on/off control register are "Don't care." When fCP or fOSC is 270 kHz, display is changed by switching every 370 ms. NW: When NW is 1, 4-line display is performed. At this time, bit N in the function set register is "Don't care."
Alternating display i) Cursor display example ii) Blink display example
Alternating display iii) White-black inverting display example a) Cursor blink width control
i) 5-dot character width
ii) 6-dot character width
b) Font width control
Figure 16 Example of Display Control
406
HD66712U
Cursor or Display Shift Cursor or display shift shifts the cursor position or display to the right or left without writing or reading display data (Table 10). This function is used to correct or search the display. In a 2-line display, the cursor moves to the second line when it passes the 40th digit of the first line. In a 4-line display, the cursor moves to the second line when it passes the 20th character of the line. Note that, all line displays will shift at the same time. When the displayed data is shifted repeatedly each line moves only horizontally. The second line display does not shift into the first line position. When this instruction is executed, extended register enable bit (RE) is reset. The address counter (AC) contents will not change if the only action performed is a display shift. In low power mode (LP = 1), whole-display shift cannot be normally performed. Scroll Enable When extended register enable bit (RE) is 1, scroll enable bits can be set. This HSE resister specifies scrolled line with the scroll quantity register. This register consists of 4 bits for each display line, so a specified line can be shifted by dot unit. When the bit 0 of HSE is 1 in four line mode (NW = 1), the first line can be shifted, and the bit 1 is specified to shift the second line, the bit 2 is specified for the third line, and bit 3 is specified for the fourth line. When it shifts the first line in two line mode (N = 1, NW = 0), both the bit 0 and bit 1 should be set to 1. The bit 2 and bit 3 is specified for the second line. In 1 line mode (N = 0, NW = 0), the bit 0 and bit 1 should be specified. Function Set Only when the extended register enable bit (RE) is 1, the BE and the LP bits shown below can be accessed. Bits DL and N can be accessed regardless of RE. DL: Sets the interface data length. Data is sent or received in 8-bit lengths (DB7 to DB0) when DL is 1, and in 4-bit lengths (DB7 to DB4) when DL is 0. When 4-bit length is selected, data must be sent or received twice. N: When bit NW in the extended function set is 0, a 1- or a 2-line display is set. When N is 0, 1-line display is selected; when N is 1, 2-line display is selected. When NW is 1, a 4-line display is set. At this time, N is "Don't care." Note: After changing the N or NW or LP bit, please issue the Return Home or Clear Display instruction to cancel to shift display.
407
HD66712U
RE: When bit RE is 1, bit BE in the extended function set register, the SEGRAM address set register, and the function set register can be accessed. When bit RE is 0, the registers described above cannot be accessed, and the data in these registers is held. To maintain compatibility with the HD44780, the RE bit should be fixed to 0. Table 10
S/C 0 0 1 1
Shift Function
R/L 0 1 0 1 Shifts the cursor position to the left. (AC is decremented by one.) Shifts the cursor position to the right. (AC is incremented by one.) Shifts the entire display to the left. The cursor follows the display shift. Shifts the entire display to the right. The cursor follows the display shift.
BE: When the RE bit is 1, this bit can be rewritten. When this bit is 1, the user font in CGRAM and the segment in SEGRAM can be blinked according to the upper two bits of CGRAM and SEGRAM. LP: When bit RE is 1, this bit can be rewritten. When LP is set to 1 and the EXT pin is low (without an extended driver), the HD66712 operates in low power mode. In 1-line display mode, the HD66712 operates on a 4-division clock, and in a 2-line or a 4-line display mode, the HD66712 operates on a 2division clock. According to these operations, instruction execution takes four times or twice as long. Note that in low power mode, display shift cannot be performed. The frame frequency is reduced to 5/6 that of normal operation. See "Oscillator Circuit" for details. Note: Perform the DL, N, NW, and FW fucntions at the head of the program before executing any instructions (except for the read busy flag and address instruction). From this point, if bits N, NW, or FW are changed after other instructions are executed, RAM contents may be broken. Set CGRAM Address A CGRAM address can be set while the RE bit is cleared to 0. Set CGRAM address into the address counter displayed by binary AAAAAA. After this address set, data is written to or read from the MPU for CGRAM. Set SEGRAM Address Only when the extended register enable (RE) bit is 1, HS2 to HS0 and the SEGRAM address can be set. The SEGRAM address in the binary form AAAA is set to the address counter. After this address set, SEGRAM can be written to or read from by the MPU.
408
HD66712U
Set DDRAM Address A DDRAM address can be set while the RE bit is cleared to 0. Set DDRAM address sets the DDRAM address binary AAAAAAA into the address counter. After this address set, data is written to or read from the MPU for DDRAM. However, when N and NW is 0 (1-line display), AAAAAAA can be (00)H to (4F)H. When N is 1 and NW is 0 (2-line display), AAAAAAA is (00)H to (27)H for the first line, and (40)H to (67)H for the second line. When NW is 1 (4-line display), AAAAAAA is (00)H to (13)H for the first line, (20)H to (33)H for the second line, (40)H to (53)H for the third line, and (60)H to (73)H for the fourth line. Set Scroll Quantity When extended registor enable bit (RE) is 1, HDS5 to HDS0 can be set. HDS5 to HDS0 specifies horizontal scroll quantity to the left of the display in dot units. The HD66712 uses the unused DDRAM area to execute a desired horizontal smooth scroll from 1 to 48 dots. Note: When performing a horizontal scroll as described above by connecting an extended driver, the maximum number of characters per line decreases by the quantity set by the above horizontal scroll. For example, when the maximum 24-dot scroll quantity (4 characters) is used with 6-dot font width and 4-line display, the maximum numbers of characters is 20 - 4 = 16. Notice that in low power mode (LP = 1), display shift and scroll cannot be performed. Read Busy Flag and Address Read busy flag and address reads the busy flag (BF) indicating that the system is now internally operating on a previously received instruction. If BF is 1, the internal operation is in progress. The next instruction will not be accepted until BF is reset to 0. Check the BF status before the next write operation. At the same time, the value of the address counter in binary AAAAAAA is read out. This address counter is used by both CG, DD, and SEGRAM addresses, and its value is determined by the previous instruction. The address contents are the same as for CGRAM, DDRAM, and SEGRAM address set instructions. Write Data to CG, DD, or SEGRAM This instruction writes 8-bit binary data DDDDDDDD to CG, DD or SEGRAM. CG, DD or SEGRAM is selected by the previous specification of the address set instruction (CGRAM address set / DDRAM address set / SEGRAM address set). After a write, the address is automatically incremented or decremented by 1 according to the entry mode. The entry mode also determines the display shift direction.
409
HD66712U
Read Data from CG, DD, or SEG RAM This instruction reads 8-bit binary data DDDDDDDD from CG, DD, or SEGRAM. CG, DD or SEGRAM is selected by the previous specification of the address set instruction. If no address is specified, the first data read will be invalid. When executing serial read instructions, the next address is normally read from the next address. An address set instruction need not be executed just before this read instruction when shifting the cursor by a cursor shift instruction (when reading from DDRAM). A cursor shift instruction is the same as a set DDRAM address instruction. After a read, the entry mode automatically increases or decreases the address by 1. However, a display shift is not executed regardless of the entry mode. Note: The address counter (AC) is automatically incremented or decremented after write instructions to CG, DD or SEGRAM. The RAM data selected by the AC cannot be read out at this time even if read instructions are executed. Therefore, to read data correctly, execute either an address set instruction or a cursor shift instruction (only with DDRAM), or alternatively, execute a preliminary read instruction to ensure the address is correctly set up before accessing the data. Table 11 HS5 to HS0 Settings
HDS5 HDS4 HDS3 HDS2 HDS1 HDS0 Description 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 . . . 1 1 0 1 1 * 1 * 1 * 1 * Shift the display position to the left by forty-seven dots. Shift the display position to the left by forty-eight dots. 0 1 0 1 No shift Shift the display position to the left by one dot. Shift the display position to the left by two dots. Shift the display position to the left by three dots.
410
HD66712U
Table 12 Instructions
Execution Time (max) (when fcp or fOSC is DB2 0 DB1 0 DB0 1 Description 270 kHz) 0 Clears entire display and 1.52 ms sets DDRAM address 0 in address counter. Sets DDRAM address 0 1.52 ms IN address counter. Also returns display from being shifted to original position. DDRAM contents remain unchanged. Sets cursor move direction and specifies display shift. These operations are performed during data write and read. 37 s
RE Instruction Bit Clear display Return home 0/1
RS 0
R/: DB7 DB6 DB5 DB4 DB3 0 0 0 0 0
:
Code
0/1
0
0
0
0
0
0
0
0
1
--
Entry mode set
0/1
0
0
0
0
0
0
0
1
I/D
S
Display on/off control
0
0
0
0
0
0
0
1
D
C
B
Sets entire display (D) 37 s on/off, cursor on/off (C), and blinking of cursor position character (B). Sets a font width, a black-white inverting cursor (B/W), and a 4line display (NW). 37 s
Extension 1 function set
0
0
0
0
0
0
1
FW
B/W
NW
Cursor or 0 display shift Scroll enable Function set 1
0
0
0
0
0
1
S/C
R/L
--
--
Moves cursor and shifts 37 s display without changing DDRAM contents. Specifies which display 37 s lines to undergo horizontal smooth scroll. Sets interface data length(DL), number of display lines (L), and extension register write enable (RE). 37 s
0
0
0
0
0
1
HSE
HSE
HSE
HSE
0
0
0
0
0
1
DL
N
RE
--
--
1
0
0
0
0
1
DL
N
RE
BE
LP
Sets CGRAM/SEGRAM 37 s blinking enable (BE), and power-down mode (LP). LP is available when the EXT pin is low. Sets CGRAM address. 37 s CGRAM data is sent and received after this setting.
Set CGRAM address
0
0
0
0
1
ACG ACG ACG
ACG
ACG
Ay
Set 1 SEGRAM address set
0
0
0
1
*
*
ASEG ASEG ASEG ASEG Sets SEGRAM address. 37 s SEGRAM data is sent and received after this setting.
411
HD66712U
Table 12 Instructions (cont)
Execution Time (max) (when fcp or fOSC is DB2 ADD DB1 ADD DB0 ADD Description 270 kHz) Sets DDRAM address. 37 s DDRAM data is sent and received after this setting. Sets horizontal dot scroll 37 s quantity. Reads busy flag (BF) indicating internal operation is being performed and reads address counter contents. Writes data into DDRAM, CGRAM, or SEGRAM. Reads data from DDRAM, CGRAM, or SEGRAM. DDRAM: ADD: 0 s
RE Instruction Bit Set DDRAM address Set scroll quantity 0
RS 0
R/: DB7 DB6 DB5 DB4 DB3 0 1 ADD ADD ADD ADD
:
Code
1
0 0
0 1
1 BF
* AC
HDS HDS HDS AC AC AC
HDS AC
HDS AC
HDS AC
Read busy 0/1 flag & address
Write data to RAM Read data from RAM
0/1
1
0
Write data
7 s tADD = 5.5 s* 37 s tADD = 5.5 s*
0/1
1
1
Read data
I/D I/D S D C B FW B/W NW NW S/C S/C R/L R/L DL N RE BE LP BF BF
= 1: Increment = 0: Decrement = 1: Accompanies display shift = 1: Display on = 1: Cursor on = 1: Blink on = 1: 6-dot font width = 1: Black-white inverting cursor on = 1: Four lines = 0: One or two lines = 1: Display shift = 0: Cursor move = 1: Shift to the right = 0: Shift to the left = 1: 8 bits, DL = 0: 4 bits = 1: 2 lines, N = 0: 1 line = 1: Extension register access enable = 1: CGRAM/SEGRAM blinking enable = 1: Low-power mode = 1: Internally operating = 0: Instructions acceptable
Display data RAM DDRAM address (corresponds to cursor address) CGRAM: Character generator RAM ACG: CGRAM address SEGRAM: Segment RAM ASEG: Segment RAM address HSE: Specifies horizontal scroll lines HDS: Horizontal dot scroll quantity AC: Address counter used for both DD, CG, and SEGRAM addresses.
Note:
1. -- indicates no effect. * After execution of the CGRAM/DDRAM data write or read instruction, the RAM address counter is incremented or decremented by 1. The RAM address counter is updated after the busy flag turns off. In Figure 17, tADD is the time elapsed after the busy flag turns off until the address counter is updated. 2. Extension time changes as frequency changes. For example, when f is 300 kHz, the execution time is: 37 s x 270/300 = 33 s. 3. Execution time in a low-power mode (LP = 1 and EXT = low) becomes four times for a 1-line mode, and twice for a 2- or 4-line mode.
412
HD66712U
Busy state (DB7 pin) Busy state
Address counter (DB0 to DB6 pins)
A t ADD
A+1
t ADD depends on the operation frequency. t ADD = 1.5/(f cp or f OSC ) seconds
Figure 17 Address Counter Update
413
HD66712U
Interfacing the HD66712 Interface with 8-Bit MPUs: The HD66712 can interface directly with an 8-bit MPU using the E clock, or with an 8-bit MCU through an I/O port. When the number of I/O ports in the MCU, or the interfacing bus width, if limited, a 4-bit interface function is used.
RS
R/W E Internal signal DB7 Data Instruction write
Internal operation Not Busy
Busy Busy flag check
Busy
Data Instruction write
Busy flag check Busy flag check
Figure 18 Example of 8-Bit Data Transfer Timing Sequence
I/O port interface
H8/325
C0 C1 C2 A0-A7 8
E RS R/W
HD66712
DB0-DB7
Figure 19 8-Bit MPU Interface
414
HD66712U
Interface with 4-Bit MPUs: The HD66712 can interface with a 4-bit MCU through an I/O port. 4-bit data representing high and low order bits must be transferred sequentially. The DL bit in function-set selects 4-bit or 8-bit interface data length.
RS R/W
E Internal signal DB7 IR7 Instruction write IR3 Internal operation Not Busy
Busy
AC3
AC3
D7
D3
Busy flag check
Busy flag check
Instruction write
Figure 20 Example of 4-Bit Data Transfer Timing Sequence
HMCS4019R D15 D14 D13 R10-R13 4 RS R/W E
HD66712
DB4-DB7
Figure 21 4-bit MPU Interface
415
HD66712U
Oscillator Circuit
1) When an external clock is used 2) When an internal oscillator is used
Clock
OSC1
Rf
OSC1 OSC2
The oscillator frequency can be adjusted by oscillator resistance (Rf). If Rf is increased or power supply voltage is decreased, the oscillator frequency decreases. The recommended oscillator resistor is as follows. i) HD66712S * Rf = 91 k 2% (VCC = 5V) * Rf = 75 k 2% (VCC = 3V) ii) HD66712U * Rf = 130 k 2% (VCC = 5V) * Rf = 110 k 2% (VCC = 3V)
HD66712
HD66712
Figure 22 Oscillator Circuit
(1) 1 /17 duty cycle
1-line selection period
1 VCC V1 COM1 V4 V5
2
3
4
16
17
1
2
3
16
17
1 frame
1 frame
Normal Display Mode (LP = 0) Item Line selection period Frame frequency 5-Dot Font Width 6-Dot Font Width 200 clocks 79.4 Hz 240 clocks 66.2 Hz
Low Power Mode (LP = 1) 5-Dot Font Width 6-Dot Font Width 60 clocks 66.2 Hz 72 clocks 55.1 Hz
Note: At the calculation example above for displayed frame frequency, all oscillator frequencies are 270 kHz (1 clock = 3.7 s).
(2) 1 /33 duty cycle
1-line selection period
1 VCC V1 COM1 V4 V5
2
3
4
32
33
1
2
3
32
33
1 frame
1 frame
Normal Display Mode (LP = 0) Item Line selection period Frame frequency 5-Dot Font Width 6-Dot Font Width 100 clocks 81.8 Hz 120 clocks 68.2 Hz
Low Power Mode (LP = 1) 5-Dot Font Width 6-Dot Font Width 60 clocks 68.2 Hz 72 clocks 56.8 Hz
Note: At the calculation example above for displayed frame frequency, all oscillator frequencies are 270 kHz (1 clock = 3.7 s).
Figure 23 Frame Frequency
416
HD66712U
Power Supply for Liquid Crystal Display Drive
1) When an external power supply is used
VCC R R R0 R R V5 VR VCC V1 V2 V3 V4
VEE
2) When an internal booster is used
(Boosting twice) VCC VCC (Boosting three times)
NTC-type thermistor GND 1 F
Vci GND C1 C2 V5OUT2 V5OUT3 1 F + GND
VCC V1 V2 R R R0 R R
NTC-type thermistor GND
Vci GND 1 F C1 C2 V5OUT2 V5OUT3
VCC V1 V2 R R R0 R R
+
V3 V4 V5
+
V3 V4 V5
1 F + 1 F
+ GND
Notes: 1. Boosting output voltage should not exceed the power supply voltage (2) (13V max.) in the absolute maximum ratings. Especially, voltage of over 4.3V should not be input to the reference voltage (Vci) when boosting three times. 2. Vci input terminal is used for reference voltage and power supply for the internal booster. Input current into the Vci pin needs three times or more of load current through the bleeder resistor for LCD. So, when it adjusts LCD driving voltage (Vlcd), input voltage should be controlled with transistor to supply LCD load current. Please notice connection (+/-) when it uses capacitors with poler. 3. The Vci must be set below the power supply (VCC).
417
HD66712U
Table 13
Item Number of Lines Duty factor Bias Divided resistance R R0 1 1/17 1/5 R R
Duty Factor and Power Supply for Liquid Crystal Display Drive
Data 2, 4 1/33 1/6.7 R 2.7R
Note: R changes depending on the size of liquid crystal panel. Normally, R must be 4.7 k to 20 k.
418
HD66712U
Extension Driver LSI Interface
By bringing the EXT pin high, extended driver interface signals (CL1, CL2, D, and M) are output. Table 14 Relationships between the Number of Display Lines and 40-Output Extension Driver
Controller HD66712 Display Lines 16 x 2 lines 20 x 2 lines 24 x 2 lines 40 x 2 lines 12 x 4 lines 16 x 4 lines 20 x 4 lines 5-Dot Width 6-Dot Width Not required Not required Not required Not required Not required 1 Disabled Disabled HD66710 5-Dot Width 6-Dot Width Not required 1 1 1 Disabled 1 1 2 1 2 Disabled 1 2 3 HD44780 5-Dot Width 1 2 2 4 Disabled Disabled Disabled HD66702 5-Dot Width Not required Not required 1 3 Disabled Disabled Disabled
Not required 1 1 1 1 2
Note: The number of display lines can be extended to 32 x 2 lines or 20 x 4 lines in the LCD-II/F12. The number of display lines can be extended to 30 x 2 lines or 20 x 4 lines in the LCD-II/F8.
a) 1-chip operation (EXT = Low, 5-dot font width)
b) When using the extension driver (EXT = High, 5-dot font width) VCC EXT
GND EXT HD66712 SEG1- SEG60 COM0- COM33 24 x 2-line display
HD66712 CL1 CL2 D M SEG1- SEG60
COM0- COM33
32 x 2-line display
SEG1-SEG60
M D Seg1- CL2 Seg40 CL1 Extension driver
Figure 24 HD66712 and the Extension Driver Connection
419
HD66712U
Table 15 Display Start Address in Each Mode
Number of Lines 1-Line Mode Output COM1-COM8 COM9-COM16 COM17-COM24 COM25-COM32 COM0/COM17 COM0/COM33 5 Dot D001 D0C1 -- -- S00 -- 6 Dot D001 D0A1 -- -- S00 -- 5 Dot D001 D0C1 D401 D4C1 -- S00 2-Line Mode 6 Dot D001 D0A1 D401 D4A1 -- S00 4-Line Mode 5 Dot/6 Dot D001 D201 D401 D601 -- S00
Notes: 1. The number of display lines is determined by setting the N/NW bit. The font width is determined by the FW bit. 2. D** is the start address of display data RAM (DDRAM). 3. S** is the start address of segment RAM (SEGRAM). 4. 1 following D** indicates increment or decrement at display shift.
420
HD66712U
Interface to Liquid Crystal Display
* Example of 5-dot font width connection
1 12 13 24
HD66712
COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM8 COM17 (COM0)
+ -x/=
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG60 COM9 COM10 COM11 COM12 COM13 COM14 COM15 COM16
EXT
Note: COM0 and COM17 output the same signals. Apply them according to the wiring pattern.
Figure 25 24 x 1-Line + 60-Segment Display (5-Dot Font, 1/17 Duty)
1 12 13 24
HD66712
COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM8 COM17 COM18 COM19 COM20 COM21 COM22 COM23 COM24 COM33 (COM0) SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG60 COM9 COM10 COM11 COM12 COM13 COM14 COM15 COM16 COM25 COM26 COM27 COM28 COM29 COM30 COM31 COM32
+ -x/=
EXT
Note: COM0 and COM33 output the same signals. Apply them according to the wiring pattern.
Figure 26 24 x 1-Line + 60-Segment Display (5-Dot Font, 1/33 Duty)
421
HD66712U
HD66712
COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM8 COM9 COM10 COM11 COM12 COM13 COM14 COM15 COM16 COM17 COM18 COM19 COM20 COM21 COM22 COM23 COM24 COM25 COM26 COM27 COM28 COM29 COM30 COM31 COM32 COM33 (COM0) SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 COM56 COM57 COM58 COM59 COM60
1
2
12
+ -x/ =
EXT
Note: COM0 and COM33 output the same signals. Apply them according to the wiring pattern.
Figure 27 12 x 4-Line + 60 Segment Display (5-Dot Font, 1/33 Duty)
HD66712
COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM8 COM17 COM18 COM19 COM20 COM21 COM22 COM23 COM24 COM33 (COM0) SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG55 SEG56 SEG57 SEG58 SEG59 SEG60 COM9 COM10 COM11 COM12 COM13 COM14 COM15 COM16 COM25 COM26 COM27 COM28 COM29 COM30 COM31 COM32
1
10
11
20
+ -x/ =
EXT
Note: COM0 and COM33 output the same signals. Apply them according to the wiring pattern.
Figure 28 20 x 2-Line + 60 Segment Display (6-Dot Font, 1/33 Duty)
422
HD66712U
Instruction and Display Correspondence
* 8-bit operation, 24-digit x 1-line display with internal reset Refer to Table 16 for an example of an 24-digit x 1-line display in 8-bit operation. The HD66712 functions must be set by the function set instruction prior to the display. Since the display data RAM can store data for 80 characters, a character unit scroll can be performed by a display shift instruction. A dot unit smooth scroll can also be performed by a horizontal scroll instruction. Since data of display RAM (DDRAM) is not changed by a display shift instruction, the display can be returned to the first set display when the return home operation is performed. * 4-bit operation, 24-digit x 1-line display with internal reset The program must set all functions prior to the 4-bit operation (see Table 17.) When the power is turned on, 8-bit operation is automatically selected and the first write is performed as an 8-bit operation. Since DB0 to DB3 are not connected, a rewrite is then required. However, since one operation is completed in two accesses for 4-bit operation, a rewrite is needed to set the functions. Thus, DB4 to DB7 of the function set instruction is written twice. * 8-bit operation, 24-digit x 2-line display with internal reset For a 2-line display, the cursor automatically moves from the first to the second line after the 40th digit of the first line has been written. Thus, if there are only 16 characters in the first line, the DDRAM address must be again set after the 16th character is completed. (See Table 18.) The display shift is performed for the first and second lines. If the shift is repeated, the display of the second line will not move to the first line. The same display will only shift within its own line for the number of times the shift is repeated. * 8-bit operation, 12-digit x 4-line display with internal reset The RE bit must be set by the function set instruction and then the NW bit must be set by an extension function set instruction. In this case, 4-line display is always performed regardless of the N bit setting (see Table 19). In a 4-line display, the cursor automatically moves from the first to the second line after the 20th digit of the first line has been written. Thus, if there are only 8 characters in the first line, the DDRAM address must be set again after the 8th character is completed. Display shifts are performed on all lines simultaneously. Note: When using the internal reset, the electrical characteristics in the Power Supply Conditions Using Internal Reset Circuit Table must be satisfied. If not, the HD66712 must be initialized by instructions. See the section, Initializing by Instruction.
423
HD66712U
Table 16
Step No. RS 1 2
8-Bit Operation, 24-Digit x 1-Line Display Example with Internal Reset
Instruction R/: DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
:
Operation Initialized. No display. Sets to 8-bit operation and selects 1-line display. Bit 2 must always be cleared. Return both display and cursor to the original position(address 0).
Power supply on (the HD66712 is initialized by the internal reset circuit) Function set 0 0 0 Return home 0 0 0 0 1 1 0 0 * *
3
0
0
0
0
0
1
0
4
Display on/off control 0 0 0 0 Entry mode set 0 0 0
0
0
1
1
1
0
_
Turns on display and cursor. Entire display is in space mode because of initialization. Sets mode to increment the address by one and to shift the cursor to the right at the time of write to the RAM. Display is not shifted. Writes H. DDRAM has already been selected by initialization when the power was turned on. Writes I. * * * * *
5
0
0
0
0
1
1
0
_
6
Write data to CGRAM/DDRAM 1 0 0 1 0 0 Write data to CGRAM/DDRAM 1 0 0 1 0 0 * * * * * Write data to CGRAM/DDRAM 1 0 0 1 0 0 Entry mode set 0 0 0 0 0 0
1
0
0
0
H_
7 8
1
0
0
1
HI_
9 10 11
1 0 0
0 1 0
0 1 0
1 1 0
HITACHI_
Writes I. Sets mode to shift display at the time of write. Writes a space.
HITACHI_
Write data to CGRAM/DDRAM 1 0 0 0 1 0
ITACHI _
424
HD66712U
Table 16
Step No. RS 12 13
8-Bit Operation, 24-Digit x 1-Line Display Example with Internal Reset (cont)
Instruction R/: DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display 1 1 0 1
TACHI M_
:
Operation Writes M.
Write data to CGRAM/DDRAM 1 0 0 1 0 0 * * * * * Write data to CGRAM/DDRAM 1 0 0 1 0 0 Cursor or display shift 0 0 0 0 Cursor or display shift0 0 0 0 0 0 1 1 0
* * * * 1 0 0 0 1 0 1 1 0 * 0 1 1 1 1 * * 1 * * 0 1 * * 1 1 *
MICROKO_
14 15 16 17 18 19 20 21
Writes O. Shifts only the cursor position to the left. Shifts only the cursor position to the left. Writes C over K. The display moves to the left. Shifts the display and cursor position to the right. Shifts the display and cursor position to the right. Writes M.
MICROKO _
MICROKO _
Write data to CGRAM/DDRAM 1 0 0 1 0 0 Cursor or display shift 0 0 0 0 Cursor or display shift 0 0 0 0 0 0 1 1
ICROCO _
MICROCO _
MICROCO_
Write data to CGRAM/DDRAM 1 0 0 1 0 0 * * * * * Return home 0 0 0 0 0 0
ICROCOM_
* * * * * 0 0 1 0
HITACHI _
22
Returns both display and cursor to the original position (address 0).
425
HD66712U
Table 17
Step No. RS 1 2
4-Bit Operation, 24-Digit x 1-Line Display Example with Internal Reset
Instruction R/: DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
:
Operation Initialized. No display. Sets to 4-bit operation. Clear bit 2. In this case, operation is handled as 8 bits by 1 initialization. * Sets 4-bit operation and selects1-line display. Clear BE, LP bits. 4-bit operation starts from this step. Sets 4-bit operation and selects1 line display. Clear bit 2 (RE). Returns both display and cursor to the original position (address 0).
Power supply on (the HD66712 is initialized by the internal reset circuit) Function set 0 0 0 -- -- -- Function set 0 0 0 0 0 0 Function set 0 0 0 0 0 0 Return home 0 0 0 0 0 0 0 -- 1 -- 0 -- -- -- -- -- -- -- -- --
3
0 1
1 0
0 0
-- --
-- --
-- --
-- --
4
0 0 0 0
1 * 0 1 0 1 0 1
0 * 0 0 0 0 0 0
-- -- -- -- -- -- -- --
-- -- -- -- -- -- -- --
-- -- -- -- -- -- -- --
-- -- -- -- -- -- -- --
_
5
6
Display on/off control 0 0 0 0 0 0 1 1 Entry mode set 0 0 0 0 0 0 0 1
Turns on display and cursor. Entire display is in space mode because of initialization. Sets mode to increment the address by one and to shift the cursor to the right at the time of write to the DD/CGRAM. Display is not shifted. Writes H. DDRAM has already been selected by initialization. Based on 8-bit operation after this instruction
7
_
8
Write data to CGRAM/DDRAM 1 0 0 1 0 0 1 0 1 0 0 0 * * * * *
-- --
-- --
-- --
-- -- * * * * *
H_
9
Note:
The control is the same as for 8-bit operation beyond step #8. 1. When DB3 to DB0 pins are open in 4-bit mode, the RE, BE, LP bits are set to "1" at step #2. So, these bits are clear to "0" at step #3.
426
HD66712U
Table 18
Step No. RS 1
8-Bit Operation, 24-Digit x 2-Line Display Example with Internal Reset
Instruction R/: DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
:
Operation Initialized. No display.
Power supply on (the HD66712 is initialized by the internal reset circuit) Function set 0 0 0
2
0
1
1
1
0
*
*
Sets to 8-bit operation and selects 2-line display. Clear bit 2.
_
3
Display on/off control 0 0 0 0 Entry mode set 0 0 0
0
0
1
1
1
0
Turns on display and cursor. All display is in space mode because of initialization. Sets mode to increment the address by one and to shift the cursor to the right at the time of write to the RAM. Display is not shifted. Writes "H." DDRAM has already been selected by initialization at power-on. * * * * * Writes I.
4
_
0
0
0
0
1
1
0
5
Write data to CGRAM/DDRAM 1 0 0 1 0 0 * * * * * Write data to CGRAM/DDRAM 1 0 0 1 0 0 Set DDRAM address 0 0 1 1
H_
1
0
0
0
6
7
1
0
0
1
HITACHI_
8
0
0
0
0
0
0
HITACHI _
Sets DDRAM address so that the cursor is positioned at the head of the second line.
427
HD66712U
Table 18
Step No. RS 9
8-Bit Operation, 24-Digit x 2-Line Display Example with Internal Reset (cont)
Instruction R/: DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
HITACHI M_
:
Operation Writes a space.
Write data to CGRAM/DDRAM 1 0 0 1 0 * * * * * Write data to CGRAM/DDRAM 1 0 0 1 0 0 Entry mode set 0 0 0 0 0 0 1 0 1 1 1 1 1 1 0 1 1 1 0 1 1 0 1
10
* * * * *
HITACHI MICROCO_ HITACHI MICROCO_ ITACHI ICROCOM_
11 12 13 14
Writes O. Sets mode to shift display at the time of write. Writes M.
Write data to CGRAM/DDRAM 1 0 0 1 0 0 * * * * * Return home 0 0 0 0 0 0
* * * * * 0 0 1 0
HITACHI _ MICROCOM
17
Returns both display and cursor to the original position (address 0).
428
HD66712U
Table 19
Step No. RS 1
8-Bit Operation, 12-Digit x 4-Line Display Example with Internal Reset
Instruction R/: DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
:
Operation Initialized. No display.
Power supply on (the HD66712 is initialized by the internal reset circuit)
2
Function set 0 0 0
0
1
1
1
1
*
*
Sets 8-bit operation and enables write to the extension register.
3
4-line mode set 0 0 0
Sets 4-line operation. 0 0 0 1 0 0 1
4
Function set Inhibit write to extension register 0 0 0 0 1 1 Display on/off control 0 0 0 0
0
0
*
*
_
Inhibits write to extension register. Invalidates selection of 1-line/2-line by bit 3. Turns on display and cursor. Entire display is cleared because of initialization. Sets mode to increment the address by one and to shift the cursor to the right when writing to RAM. Display is not shifted. Writes H. DDRAM has already been selected by initialization.
5
0
0
1
1
1
0
6
Entry mode set 0 0 0
0
0
0
0
1
1
0
_
7
Write data to CGRAM/DDRAM 1 0 0 1 0 0
_
1
0
0
0
8
* * * * *
* * * * *
429
HD66712U
Table 19
Step No. RS 9
8-Bit Operation, 12-Digit x 4-Line Display Example with Internal Reset (cont)
Instruction R/: DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
HITACHI_
:
Operation Writes I.
Write data to CGRAM/DDRAM 1 0 0 1 0 0
1
0
0
1
10
Set DDRAM address 0 0 1 0
1
0
0
0
0
0
HITACHI _
Sets DDRAM address to (20)H so that the cursor is positioned at the beginning of the second line. Writes 0.
11
Write data to CGRAM 1 0 0 0
1
1
0
0
0
0
HITACHI 0_
430
HD66712U
Initializing by Instruction
If the power supply conditions for correctly operating the internal reset circuit are not met, initialization by instructions becomes necessary. * Initializing when a length of interface is 8-bit system. (See Figure 29.) * Initializing when a length of interface is 4-bit system. (See Figure 30.)
Power on
* Wait for more than 15 ms after VCC rises to 4.5V (VCC = 5V during operation) * Wait for more than 40 ms after VCC rises to 2.7V (VCC = 3V during operation)
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 000011****
BF cannot be checked before this instruction. Function set (Interface is 8 bits long.)
Wait for more than 4.1 ms
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 000011****
BF cannot be checked before this instruction. Function set (Interface is 8 bits long.)
Wait for more than 100 s
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 000011****
BF cannot be checked before this instruction. Function set (Interface is 8 bits long.)
BF can be checked after the following instructions. When BF is not checked, the waiting time between instructions is longer than the execution instruction time. (See Table 12.) RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 000011N0** 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 1 Function set Display off Display clear Entry mode set
I/D S
Initialization ends
Figure 29 Initializing Flow of 8-Bit Interface
431
HD66712U
Power on Important Notice Notes: 1. When DB3 to DB0 pins are open in 4-bit mode, the N, RE, BE, LP bits are set to "1." In this case, instruction time becomes four times in a low power mode (LP = "1"). 2. The low power mode is available in this step, so instruction time takes four times.
* Wait for more than 15 ms after VCC rises to 4.5V (VCC = 5V during operation) * Wait for more than 40 ms after VCC rises to 2.7V (VCC = 3V during operation)
RS R/W DB7 DB6 DB5 DB4 000011
BF cannot be checked before this instruction. Function set (Interface is 8 bits long)
Wait for more than 4.1 ms
RS R/W DB7 DB6 DB5 DB4 000011
BF cannot be checked before this instruction. Function set (Interface is 8 bits long)
Wait for more than 100 s
RS R/W DB7 DB6 DB5 DB4 000011
*1
BF cannot be checked before this instruction. Function set (Interface is 8 bits long) BF can be checked after the following instructions. When BF is not checked, the waiting time between instructions is longer than the execution instruction time. (See Table 12.)*1
RS R/W DB7 DB6 DB5 DB4 000010 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 N 0 N 0 1 0 0 0 0 0 1 0 0 0 0 0 0 0 1 10 00 10 ** 00 00 00 01 00 I/D S
*1 *2
Function set (4-bit mode) Function set (4-bit mode, N specification) BE, LP are clear to 0 Function set (4-bit mode, N specification) Display off Display clear Entry mode set (I/D, S specification)
Initialization ends
Figure 30 Initializing Flow of 4-Bit Interface
432
HD66712U
Horizontal Dot Scroll
Dot unit scrolls are performed by setting the horizontal dot scroll quantity resister (HDS) when the extension register is enabled (RE = "1"). And the shifted line can be selected with the scroll enable register (HDE). So, it can control dot unit shifts by each display line. To scroll smoothly, HD66712 supports 6 dots-font width mode (FW = 1). The below figures are examples of scroll display.
When 5-dots font width (FW = 0) No shift performed When 6-dots font width (FW = 1)
No shift performed
One dot shift to the left
One dot shift to the left
Two dots shift to the left
Two dots shift to the left
Three dots shift to the left
Three dots shift to the left
Four dots shift to the left
Four dots shift to the left
Five dots shift to the left
Example of 10 digits x 4 lines with 6-dots fonts width mode
ICON mark and 1st to 3rd line are fixed, and only 4th line is sifted HDS = 1000 (4th line scroll enable)
Figure 31 Example of Dot Scroll Display
433
HD66712U
6-dots font width mode (FW = 1) 4 line display mode (NW = 1)
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
1 2 3
0 0 0
0 0 0
0 0 1
0 0 0
1 0 0
DL N 1 0 1 0
1 0 0
BE LP 0 0 0 1
Enable extension resistor. 4th line scroll enable. One dot shift in 4th line to the left.
CPU Wait 4 0 0 1 0 0 0 0 0 1 0 Two dots shift in 4th line to the left.
CPU Wait 5 0 0 1 0 0 0 0 0 1 1 Three dots shift in 4th line to the left.
CPU Wait 6 0 0 1 0 0 0 0 1 0 0 Four dots shift in 4th line to the left.
CPU Wait
49
0
0
1
1
1
0
1
1
1
1
47 dots shift in 4th line to the left.
CPU Wait 50 0 0 1 0 1 1 0 0 0 0 48 dots shift in 4th line to the left.
Note: When perfoming a dot scroll with an extended driver, the maximum number or characters per line decreases by quantity set by the dot scroll. For example, when the maximum 24-dot scroll quantity (4 characters) is used with 6-dot font width and 4-line display, the maximum numbers of character is 20 - 4 = 16. Notice that in low power mode (LP = 1), display shift and dot scroll cannot be performed.
Figure 32 Method of Smooth Scroll Display
434
HD66712U
Low Power Mode When the extension driver is not used (EXT = Low) with extension register enabled (RE = 1), the HD66712 enters low power mode by setting the low-power mode bit (LP) to 1. During low-power mode, as the internal operation clock is divided by 2 (2-line/4-line display mode) or by 4 (1-line display mode), the execution time of each instruction becomes two times or four times longer than normal. In addition, as the frame frequency decreases to 5/6, display quality might be affected. In addition, since the display is not shifted in low power mode, display shift must be cleared with the return home instruction before setting low power mode. The amount of horizontal scroll must also be cleared (HDS = 000000). Moreover, because the display enters a shift state after clearing low-power mode, the home return instruction must be used to clear display shift at that time.
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Return home 0 0 0 0 0 0 0 0 1 0
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Extended register enable 0 0 0 0 1 DL N 1 BE 0
Clear horizontal scroll quantity HDS = 000000
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 0 0 1 0 0 0 0 0 0 0
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Set a low power mode 0 0 0 0 1 DL N 1 BE 1
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Return home 0 0 0 0 0 0 0 0 1 0
Low power operation
Note: The execution time of an instruction in low-power mode becomes two times or four times longer then normal. The frame frequency also decreases by 5/6.
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Clear low power mode 0 0 0 0 1 DL N 1 BE 0
Note: Up until this instruction, execution time is two times or four times longer than normal. RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Return home 0 0 0 0 0 0 0 0 1 0
Note: Because the display enters a shift state, be sure to execute this instruction.
Figure 33 Usage of Low Power Mode
435
HD66712U
Absolute Maximum Ratings*
Item Power supply voltage (1) Power supply voltage (2) Input voltage Operating temperature Storage temperature Note: * Symbol VCC VCC-V5 Vt Topr Tstg Unit V V V C C Value -0.3 to +7.0 -0.3 to +13.0 -0.3 to VCC +0.3 -20 to +75 -55 to +125 4 Notes 1 1, 2 1
If the LSI is used above these absolute maximum ratings, it may become permanently damaged. Using the LSI within the following electrical characteristic limits is strongly recommended for normal operation. If these electrical characteristic conditions are also exceeded, the LSI will malfunction and cause poor reliability.
436
HD66712U
DC Characteristics (VCC = 2.7V to 5.5V, Ta = -20 to +75C*3)
Item Input high voltage (1) (except OSC1) Input low voltage (1) (except OSC1) Input high voltage (2) (OSC1) Input low voltage (2) (OSC1) Symbol Min VIH1 VIL1 0.7VCC -0.3 -0.3 VIH2 VIL2 0.7VCC -- 0.75VCC -- 0.8VCC -- -- Typ -- -- -- -- -- -- -- -- -- 2 Max VCC 0.2VCC 0.6 VCC 0.2VCC -- 0.2VCC -- 0.2VCC 20 Unit V V V V V V V V V k -IOH = 0.1 mA IOL = 0.1 mA -IOH = 0.04 mA IOL = 0.04 mA Id = 0.05 mA (COM) VLCD = 4V Id = 0.05 mA (SEG) VLCD = 4V VIN = 0 to VCC VCC = 3V VIN = 0V Rf oscillation external clock VCC = 3V fosc = 270 kHz 10, 14 VCC = 2.7 to 3.0V VCC = 3.0 to 4.5V 15 15 7 7 8 8 13 Test Condition Notes* 6 6
Output high voltage (1) VOH1 (D0-D7) Output low voltage (1) (D0-D7) VOL1
Output high voltage (2) VOH2 (except D0-D7) Output low voltage (2) (except D0-D7) Driver ON resistance (COM) Driver ON resistance (SEG) I/O leakage current Pull-up MOS current (D0-D7, RESET* pin) VOL2 RCOM
RSEG
--
2
30
k
13
ILI -Ip
-1 10 -- -- -- 2.7 2.7
-- 50 130 90 65 -- --
1 120 300 -- -- 11.0 11.0
A A A A A V V
9
Current Normal ICC consumption display (HD66712U) LP mode1 I LP1 (1/33duty) LP mode2 ILP2 (1/17duty) LCD voltage Note: * VLCD1 VLCD2
VCC-V5, 1/5 bias VCC-V5, 1/6.7 bias
16 16
Refer to Electrical Characteristics Notes following these tables.
437
HD66712U
Booster Characteristics
Item Output voltage (V5OUT2 pin) Output voltage (V5OUT3 pin) Input voltage Note: * Symbol VUP2 Min 7.5 Typ 8.7 Max -- Unit V Test Condition Vci = 4.5V, I0 = 0.25 mA, C = 1 F, fOSC = 270 kHz Ta = 25C Vci = 2.7V, I0 = 0.25 mA, C = 1 F, fOSC = 270 kHz Ta = 25C Vci VCC Ta = 25C Notes* 18, 19
VUP3
7.0
7.7
--
V
18, 19
VCi
1.0
--
5.0
V
18, 19
Refer to Electrical Characteristics Notes following these tables.
AC Characteristics (VCC = 2.7V to 5.5V, Ta = -20 to +75C*3)
Clock Characteristics (VCC = 2.7V to 5.5V, Ta = -20 to +75C* )
Item External External clock frequency clock External clock duty operation External clock rise time External clock fall time Symbol fcp Duty trcp trcp Min 125 45 -- -- 190 Typ 270 50 -- -- 270 Max 410 55 0.2 0.2 350 Unit kHz % s s kHz Rf = 130 k, VCC = 5V HD66712U 12 Test Condition Notes* 11
3
Clock oscillation frequency fOSC Rf oscillation Note: *
Refer to the Electrical Characteristics Notes section following these tables.
438
HD66712U
System Interface Timing Characteristics (1) (VCC = 2.7V to 4.5V, Ta = -20 to +75C*3)
Bus Write Operation
Item Enable cycle time Enable pulse width (high level) Enable rise/fall time Address set-up time (RS, R/W to E) Address hold time Data set-up time Data hold time Symbol Min tcycE PWEH tEr, tEf tAS tAH tDSW 1000 450 -- 60 20 195 Typ -- -- -- -- -- -- Max -- -- 25 -- -- -- Unit ns Test Condition Figure 34
tH
10
--
--
Bus Read Operation
Item Enable cycle time Enable pulse width (high level) Enable rise/fall time Address set-up time (RS, R/W to E) Address hold time Data delay time Data hold time Symbol Min tcycE PWEH tEr, tEf tAS tAH tDDR tDHR 1000 450 -- 60 20 -- 5 Typ -- -- -- -- -- -- -- Max -- -- 25 -- -- 360 -- Unit ns Test Condition Figure 35
439
HD66712U
Serial Interface Operation
Item Serial clock cycle time Serial clock (high level width) Serial clock (low level width) Serial clock rise/fall time Chip select set-up time Chip select hold time Serial input data set-up time Serial input data hold time Serial output data delay time Serial output data hold time Symbol tSCYC tSCH tSCL tSCr, tSCf tCSU tCH tSISU tSIH tSOD tSOH Min 1 400 400 -- 60 200 200 200 -- 0 Typ -- -- -- -- -- -- -- -- -- -- -- 360 -- Max 20 -- -- 50 -- -- Unit s ns Test Condition Figure 36
440
HD66712U
System Interface Timing Characteristics (2) (VCC = 4.5V to 5.5V, Ta = -20 to +75C*3)
Bus Write Operation
Item Enable cycle time Enable pulse width (high level) Enable rise/fall time Address set-up time (RS, R/W to E) Address hold time Data set-up time Data hold time Symbol Min tcycE PWEH tEr, tEf tAS tAH tDSW tH 500 230 -- 40 10 80 10 Typ -- -- -- -- -- -- -- Max -- -- 20 -- -- -- -- Unit ns Test Condition Figure 34
Bus Read Operation
Item Enable cycle time Enable pulse width (high level) Enable rise/fall time Address set-up time (RS, R/W to E) Address hold time Data delay time Data hold time Symbol Min tcycE PWEH tEr, tEf tAS tAH tDDR tDHR 500 230 -- 40 10 -- 5 Typ -- -- -- -- -- -- -- Max -- -- 20 -- -- 160 -- Unit ns Test Condition Figure 35
441
HD66712U
Serial Interface Sequence
Item Serial clock cycle time Serial clock (high level width) Serial clock (low level width) Serial clock rise/fall time Chip select set-up time Chip select hold time Serial input data set-up time Serial input data hold time Serial output data delay time Serial output data hold time Symbol tSCYC tSCH tSCL tSCr, tSCf tCSU tCH tSISU tSIH tSOD tSOH Min 0.5 200 200 -- 60 100 100 100 -- 0 Typ -- -- -- -- -- -- -- -- -- -- Max 20 -- -- 50 -- -- -- -- 160 -- Unit s ns Test Condition Figure 36
Segment Extension Signal Timing (VCC = 2.7V to 5.5V, Ta = -20 to +75C*3)
Item Clock pulse width High level Low level Clock set-up time Data set-up time Data hold time M delay time Clock rise/fall time Symbol tCWH tCWL tCSU tSU tDH tDM tct Min 800 800 500 300 300 -1000 -- Typ -- -- -- -- -- -- -- Max -- -- -- -- -- 1000 100 Unit ns Test Condition Figure 37
Reset Timing (VCC = 2.7V to 5.5V, Ta = -20 to +75C*3)
Item Reset low-level width Symbol tRES Min 10 Typ -- Max -- Unit ms Test Condition Figure 38
Power Supply Conditions Using Internal Reset Circuit
Item Power supply rise time Power supply off time Symbol trCC tOFF Min 0.1 1 Typ -- -- Max 10 -- Unit ms Test Condition Figure 39
442
HD66712U
Electrical Characteristics Notes
1. All voltage values are referred to GND = 0V. If the LSI is used above the absolute maximum ratings, it may become permanently damaged. Using the LSI within the following electrical characteristic is strongly recommended to ensure normal operation. If these electrical characteristic are also exceeded, the LSI may malfunction or exhibit poor reliability. 2. VCC V1 V2 V3 V4 V5 must be maintained. 3. For die products, specified up to 75C. 4. For die products, specified by the die shipment specification. 5. The following four circuits are I/O pin configurations except for liquid crystal display output.
Input pin Pin: E/SCLK, RS/CS*, RW/SID, IM, Pins: RESET* (MOS with pull-up) EXT, TEST (MOS without pull-up) VCC VCC VCC PMOS PMOS PMOS Output pin Pins: CL1, CL2, M, D VCC PMOS
(pull-up MOS) NMOS NMOS NMOS
I/O Pin Pins: DB0/SOD-DB7 (MOS with pull-up)
VCC PMOS
VCC (input circuit) PMOS Input enable
(pull-up MOS)
NMOS VCC NMOS PMOS
Output enable Data
NMOS (output circuit) (tristate)
6. 7. 8. 9.
Applies to input pins and I/O pins, excluding the OSC1 pin. Applies to I/O pins. Applies to output pins. Current flowing through pull-up MOSs, excluding output drive MOSs.
443
HD66712U
10. Input/output current is excluded. When input is at an intermediate level with CMOS, the excessive current flows through the input circuit to the power supply. To avoid this from happening, the input level must be fixed high or low. 11. Applies only to external clock operation.
Th Oscillator OSC1 0.7 VCC 0.5 VCC 0.3 VCC Tl
Open
OSC2
tfcp Th Duty = x 100% Th + Tl
tfcp
12. Applies only to the internal oscillator operation using oscillation resistor Rf.
i) HD66712S
OSC1 Rf OSC2
R f : 75 k 2% (when VCC = 3V to 4V) R f : 91 k 2% (when VCC = 4V to 5V)
ii) HD66712U
Rf : 110 k 2% (when VCC = 3V to 4V) Rf : 130 k 2% (when VCC = 4V to 5V) Since the oscillation frequency varies depending on the OSC1 and OSC2 pin capacitance, the wiring length to these pins should be minimized.
Referential data VCC = 5V 400 fOSC (kHz) fOSC (kHz) 400 VCC = 3V
300
270
300
270
200 50
91
HD66712U (typ.) HD66712S (typ.)
200 50
75
HD66712U (typ.) HD66712S (typ.)
100
130
150
100
110
150
Rf (k)
Rf (k)
444
HD66712U
13. RCOM is the resistance between the power supply pins (VCC, V1, V4, V5) and each common signal pin (COM0 to COM33). RSEG is the resistance between the power supply pins (VCC, V2, V3, V5) and each segment signal pin (SEG1 to SEG60). 14. The following graphs show the relationship between operation frequency and current consumption.
VCC = 5V 1.8 1.6 1.4 1.2 ICC (mA) 1.0 0.8 0.6 0.4 0.2 0.0 0 100 200 300 400 500 typ. max. ICC (mA) 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 100 200 300 400 typ. (normal mode) typ. (low power mode) 500 max. (normal mode) VCC = 3V
fOSC or fcp (kHz)
fOSC or fcp (kHz)
15. Applies to the OSC1 pin. 16. Each COM and SEG output voltage is within 0.15V of the LCD voltage (VCC, V1, V2, V3, V4, V5) when there is no load. 17. The TEST pin must be fixed to ground, and the IM or EXT pin must also be connected to VCC or ground. 18. Booster characteristics test circuits are shown below.
(Boosting twice) (Boosting three times)
VCC
Vci C1 C2 V5OUT2 + + 1 F
Rload IO
VCC
Vci C1 C2 V5OUT2 + + 1 F
Rload IO
1 F
1 F
V5OUT3 GND
V5OUT3 GND +
1 F
445
HD66712U
19. Reference data The following graphs show the liquid crystal voltage booster characteristics. VUP2 = VCC-V5OUT2 VUP3 = VCC-V5OUT3
(1) VUP2, VUP3 vs Vci
Boosting twice 11 10 9 8 7 6 5 4 typ. VUP3 (V) 15 14 13 12 11 10 9 8 7 6 2.0 Boosting three times typ.
VUP2 (V)
2.0
3.0
4.0 Vci (V)
5.0
3.0
4.0 Vci (V)
5.0
Test condition: Vci = VCC, fcp = 270 kHz, Ta = 25C, Rload = 25 k
Test condition: Vci = VCC, fcp = 270 kHz, Ta = 25C, Rload = 25 k
(2) VUP2, VUP3 vs Io
Boosting twice 9.0 8.5 VUP2 (V) 8.0 7.5 7.0 6.5 6.0 0.0 0.5 1.0 Io (mA) 1.5 2.0 typ. min. 8.0 7.5 VUP3 (V) 7.0 6.5 6.0 5.5 5.0 0.0 0.5 1.0 Io (mA) 1.5 typ. min. 2.0 Boosting three times
Test condition: Vci = VCC = 4.5V, Rf = 91 k, Ta = 25C
Test condition: Vci = VCC = 2.7V, Rf = 75 k, Ta = 25C
(3) VUP2, VUP3 vs Ta
Boosting twice 9.0 8.5 VUP2 (V) 8.0 7.5 7.0 -60 typ. min. VUP3 (V) 8.0 7.5 7.0 6.5 6.0 -60 typ. min. Boosting three times
-20 0 20 60 Ta (C)
100
-20 0 20 60 Ta (C)
100
Test condition: Vci = VCC = 4.5V, Rf = 91 k, Io = 0.25 mA
Test condition: Vci = VCC = 2.7V, Rf = 75 k, Io = 0.25 mA
446
HD66712U
(4) VUP2, VUP3 vs capacitance
Boosting twice 9.0 8.5 VUP2 (V) 8.0 7.5 7.0 0.5 1.0 C (F) 1.5 typ. min. VUP2 (V) 8.0 7.5 7.0 6.5 6.0 Boosting three times typ. min.
0.5
1.0 C (F)
1.5
Test condition: Vci = VCC = 4.5V, Rf = 91 k, Io = 0.25 mA
Test condition: Vci = VCC = 2.7V, Rf = 75 k, Io = 0.25 mA
20. Must maintain ("High") VCC Vci ("Low").
447
HD66712U
Load Circuits
AC Characteristics Test Load Circuits
Data bus: DB0-DB7, SOD Segment extension signals: CL1, CL2, D, M
Test point 50 pF
Test point 30 pF
448
HD66712U
Timing Characteristics
RS VIH1 VIL1 t AS t AH VIH1 VIL1
R/W
VIL1 PWEH t AH t Ef
VIL1
E t Er
VIH1 VIL1 t DSW
VIH1 VIL1 tH
VIL1
DB0 to DB7
VIH1 VIL1
Valid data tCYCE
VIH1 VIL1
Figure 34 Bus Write Operation
VIH1 VIL1 t AS t AH VIH1 VIL1
RS
R/W
VIH1 PWEH t AH t Ef
VIH1
E t Er
VIH1 VIL1 t DDR
VIH1 VIL1 t DHR
VIL1
DB0 to DB7
VOH1 VOL1
Valid data tCYCE
VOH1 VOL1
Figure 35 Bus Read Operation
449
HD66712U
tSCYC CS* VIL1 tCSU tSCr tSCH tSCf tCWL tCH VIL1
SCLK
VIH1 VIL1
VIL1 tSISU VIH1 VIL1 tSOD
VIH1 VIL1 tSIH VIH1 VIL1
VIL1
VIH1
SID
tSOH VOH1 VOL1 VOH1 VOL1
SOD
Figure 36 Serial Interface Timing
t ct CL1 VOH2 VOH2 t CWH t CWH CL2 VOH2 t CSU t CWL t ct
VOH2 VOL2
VOL2
VOL2
D t DH t SU M VOL2 t DM
Figure 37 Interface Timing with Extension Driver
450
HD66712U
tRES
RESET* VIL1 VIL1
Note: When power is supplied, initializing by the internal reset circuit has priority. Accordingly, the above RESET* input is ignored during internal reset period.
Figure 38 Reset Timing
VCC
2.7V/4.5V
*2
0.2V
0.2V
0.2V
t rcc 0.1 ms t rcc 10 ms
t OFF *1 t OFF 1 ms
Notes: 1. tOFF compensates for the power oscillation period caused by momentary power supply oscillations. 2. Specified at 4.5V for 5-volt operation, and at 2.7V for 3-volt operation. 3. If the above electrical conditions are not satisfied, the internal reset circuit will not operate normally. In this case, initialized by instruction. (Refer to the Initializing by Instruction section.)
Figure 39 Power Supply Sequence
451

▲Up To Search▲

Price & Availability of HD66712

	To Download HD66712 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .